Every Maker Should Have [Pt.41]...SMD LCR-Tweezers (MS8911)
Product review and demo starts at 11:40.
Introducing the MASTECH MS8911: A fully fledged SMD-LCR meter for measuring components in-circuit for around 40 Euros only!
Support Roger on Patreon: https://www.patreon.com/kainkalabs
Availabe in Europe at Elektor-magazine:
https://www.elektor.com/mastech-ms8911-smart-smd-tester-lcr-meter
The poor man´s version of the "Smart Tweezers":
http://www.smarttweezers.com/
Measurement voltage can be changed from 500mV-RMS to 100mV-RMS so that semiconductors in parallel to your component don´t turn on.
Dual display (Q-factor/Dissipation factor), 100Hz...10kHz selectable test-frequency, auto-mode or manual L/C/ESR/DC-R selection, 6000 counts, 1.5...3% accuracy
The downsides:
1.) The slotted tweezer-tips are totally crap.
You have to replace them with sharp ones.
Not easy or cheap to find!
If you have a link for cheap replacement tips please post them in the comments!
2.) Last settings (especially test-frequency & test-voltage) are not stored after power-off
3.) Auto power-off time cannot be changed.
Full specs:
http://www.mastech-group.com/products.php?cate=104&PNo=78
A useful complementary SMD-Tester with 4V diode test-voltage:
MASTECH MS89119A:
http://www.mastech-group.com/products.php?cate=104&PNo=77#_
Видео Every Maker Should Have [Pt.41]...SMD LCR-Tweezers (MS8911) канала KainkaLabs
Introducing the MASTECH MS8911: A fully fledged SMD-LCR meter for measuring components in-circuit for around 40 Euros only!
Support Roger on Patreon: https://www.patreon.com/kainkalabs
Availabe in Europe at Elektor-magazine:
https://www.elektor.com/mastech-ms8911-smart-smd-tester-lcr-meter
The poor man´s version of the "Smart Tweezers":
http://www.smarttweezers.com/
Measurement voltage can be changed from 500mV-RMS to 100mV-RMS so that semiconductors in parallel to your component don´t turn on.
Dual display (Q-factor/Dissipation factor), 100Hz...10kHz selectable test-frequency, auto-mode or manual L/C/ESR/DC-R selection, 6000 counts, 1.5...3% accuracy
The downsides:
1.) The slotted tweezer-tips are totally crap.
You have to replace them with sharp ones.
Not easy or cheap to find!
If you have a link for cheap replacement tips please post them in the comments!
2.) Last settings (especially test-frequency & test-voltage) are not stored after power-off
3.) Auto power-off time cannot be changed.
Full specs:
http://www.mastech-group.com/products.php?cate=104&PNo=78
A useful complementary SMD-Tester with 4V diode test-voltage:
MASTECH MS89119A:
http://www.mastech-group.com/products.php?cate=104&PNo=77#_
Видео Every Maker Should Have [Pt.41]...SMD LCR-Tweezers (MS8911) канала KainkaLabs
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Smart Tweezers ST5S (Colibri Pro) LCR Meter Video Overview3 Ways to Check Capacitors in Circuit with Meters & TestersEvery Maker should have...[Pt.34]...a good PCB-HolderSMD bad capacitor test / laptop - desktop computer & electronics troubleshootingAven (MasTech) 18910 Smart SMD Tweezers Tester Review - More Gadget Tech ThoughtsUNI-T UT116A UT116C SMD TesterEvery Maker Should Have...[Pt.45]...a PCBite-KitEvery Maker should have...[Pt.37]...a Rubidium Frequency Standard2006 Ford Escape ECM repairHow to remove SMD components without hot air gunEvery Maker Should Have...[Pt.42]...a 555 Timer KitTwo Very Good/Low Priced Items For Electronics Hobbyists(LCR & IC)EEVblog 1378 - NEW Uni-T UT61E+ Multimeter - Still bang-per-buck king?LCR and Transistor Tester Comparisonhow to test a RUN or START CAPACITOR the CORRECT wayEvery maker should have…[Pt.31]...a good magnifier, a loupe & good lightingUT116C vs DT71Measuring Capacitance and ESR - Workbench WednesdaysThe Best Multimeter Tutorial in The World (How to use & Experiments)