1000mm/s: RELAXED TESTING
I started with a V0.0 Kit from Aliexpress (now it's 0.1, which is better in any respect)*:
Formbot Voron V0.1 Kit (AliExpress) https://bit.ly/39kfWdC
LDO Voron V0.1 KIT (Caribou3D) https://bit.ly/3KBxqzL
Recommended Kits for bigger DIY printers:
Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE
Voron Trident Kit (AliExpress) https://bit.ly/3yxMaNe
STL files, instructions and BOM on the recent upgrades:
https://247printing.gumroad.com/l/247zeroBeta1
Support my work at Patreon:
https://www.patreon.com/247printing
My Instagram and Twitter - more about my doings and behind the scenes:
Instagram: https://www.instagram.com/247printing/
Twitter: https://twitter.com/247_printing
Watch the print at 1100mm/s:
https://youtube.com/shorts/oy9C-VDsu-k?feature=share
💚Pizza, Beer and Coffee helps me going on💚
https://paypal.me/247printing
💚Thanks to all who support/ed my work💚
---------------Settings:
Filament: ESUN ABS+ - a great choice filament for strong parts and easy printing
https://amzn.to/3Bi0x7k
T_Hotend = 290C
T_Bed = 90C
Requested Speed: 1000mm/s
Acceleration: 35.000 mm/s²
square_corner_velocity: 15mm/s
Nozzle: 0.4mm
Layer Height: 0.1mm
Line width: 0.4mm
Volumetric flow: 40mm³/s
Lengths of straights: 65mm
Lengths of printing @ REAL 1000mm/s: 35mm
Xxxx ALL DESIGNS AVAILABLE SOON xxxX
@ Voron Users / Thingiverse
*******UPGRADES* STAGE 1 on my Voron V0 - VIDEO DEEP DIVES and ANALYSES incoming:
For years now, I use BigTreeTech/BIQU products - very much recommended:
(I was sponsored with an Octopus Board V1.1, TMC2209, 70W Heater and PT1000 thermistor)
Get the Octopus Board here:
https://bit.ly/31kKCrj
—MOTION (Part 1: Video Deep Dive incoming)
Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S)
https://amzn.to/3kBO5tm
F623 bearings instead of toothed idlers
https://amzn.to/2UktSgZ
WD40 specialist dry lubricant for rails (PTFE)
https://amzn.to/3ziGaF4
Gates-LL-2GT 6mm belts
https://amzn.to/3kCaAht
— EXTRUSION: (Part 2: Video Deep Dive)
Slice Engineering Mosquito Magnum (5% off!): https://www.sliceengineering.com?p=rkjO5IsbY
VolcoMosq Block (+9mm melt): https://www.youtube.com/watch?v=_2xph8QkcpU&t=18s
E3D Hemera (Bowden config)
https://amzn.to/3zdvAzk
Capricorn Bowden Tube
https://amzn.to/3kBrgWE
50W heater (24V)
https://amzn.to/2UmOIwa
PT1000 temp sensor
https://amzn.to/3ivfdY2
Boron Nitride Paste @ heater, thermistor and heat break
https://amzn.to/3kvPem6
— COOLING (Part 3: Video Deep Dive)
4010 blower fans (24V), updated toolhead
https://amzn.to/3irazKT
optimized air ducts for part cooling with aluminium tape insulation
https://amzn.to/3zhbuEs
External Static Cooling: 4x4020 fans (24V)
https://amzn.to/3zcap0D
4x40mm heatsink at AB stepper motors
https://amzn.to/3irvLAh
2x 4020 / or 4010 fans (5V) at heat sinks (stepper motors)
https://amzn.to/3wOmfMJ
25mm axial fan (5V) for stepper drivers
https://amzn.to/3eDf4AW
— Software / Firmware / Controllers (Part 4: Video Deep Dive):
Klipper
https://www.klipper3d.org/
Raspberry Pi Zero W (Mainsail)
https://amzn.to/3xR9l21
Raspberry Pi 3B (Input Shaping and Octoprint)
https://amzn.to/2UwIMAu
Alternative: Raspberry Pi4:
https://amzn.to/3kBt4io
Simplify 3D: multi processes used
https://www.simplify3d.com/
-------------------------------------------------------
My modest video gear*:
iPhone 11 Pro: https://amzn.to/2VZYswJ
Smartphone video rig: https://amzn.to/3iriub5
GoPro Hero 9: https://amzn.to/2UZI9Q5
FLIR ONE PRO: https://amzn.to/2UWAe67
Similar to the soft boxes I use: https://amzn.to/3xRes2d
Similar to the tripod I use: https://amzn.to/2V1I6mw
*Amazon links are affiliate links at no extra costs for you!
#JoinTheSpeed
#247printing
#volcomosq
#SpeedBoatRace
Видео 1000mm/s: RELAXED TESTING канала 247printing
Formbot Voron V0.1 Kit (AliExpress) https://bit.ly/39kfWdC
LDO Voron V0.1 KIT (Caribou3D) https://bit.ly/3KBxqzL
Recommended Kits for bigger DIY printers:
Voron 2.4 Kit (AliExpress) kit bit.ly/3PklmWE
Voron Trident Kit (AliExpress) https://bit.ly/3yxMaNe
STL files, instructions and BOM on the recent upgrades:
https://247printing.gumroad.com/l/247zeroBeta1
Support my work at Patreon:
https://www.patreon.com/247printing
My Instagram and Twitter - more about my doings and behind the scenes:
Instagram: https://www.instagram.com/247printing/
Twitter: https://twitter.com/247_printing
Watch the print at 1100mm/s:
https://youtube.com/shorts/oy9C-VDsu-k?feature=share
💚Pizza, Beer and Coffee helps me going on💚
https://paypal.me/247printing
💚Thanks to all who support/ed my work💚
---------------Settings:
Filament: ESUN ABS+ - a great choice filament for strong parts and easy printing
https://amzn.to/3Bi0x7k
T_Hotend = 290C
T_Bed = 90C
Requested Speed: 1000mm/s
Acceleration: 35.000 mm/s²
square_corner_velocity: 15mm/s
Nozzle: 0.4mm
Layer Height: 0.1mm
Line width: 0.4mm
Volumetric flow: 40mm³/s
Lengths of straights: 65mm
Lengths of printing @ REAL 1000mm/s: 35mm
Xxxx ALL DESIGNS AVAILABLE SOON xxxX
@ Voron Users / Thingiverse
*******UPGRADES* STAGE 1 on my Voron V0 - VIDEO DEEP DIVES and ANALYSES incoming:
For years now, I use BigTreeTech/BIQU products - very much recommended:
(I was sponsored with an Octopus Board V1.1, TMC2209, 70W Heater and PT1000 thermistor)
Get the Octopus Board here:
https://bit.ly/31kKCrj
—MOTION (Part 1: Video Deep Dive incoming)
Nema14 spec Voron V0.1 @1.7A (OMC 14HS20-1504S)
https://amzn.to/3kBO5tm
F623 bearings instead of toothed idlers
https://amzn.to/2UktSgZ
WD40 specialist dry lubricant for rails (PTFE)
https://amzn.to/3ziGaF4
Gates-LL-2GT 6mm belts
https://amzn.to/3kCaAht
— EXTRUSION: (Part 2: Video Deep Dive)
Slice Engineering Mosquito Magnum (5% off!): https://www.sliceengineering.com?p=rkjO5IsbY
VolcoMosq Block (+9mm melt): https://www.youtube.com/watch?v=_2xph8QkcpU&t=18s
E3D Hemera (Bowden config)
https://amzn.to/3zdvAzk
Capricorn Bowden Tube
https://amzn.to/3kBrgWE
50W heater (24V)
https://amzn.to/2UmOIwa
PT1000 temp sensor
https://amzn.to/3ivfdY2
Boron Nitride Paste @ heater, thermistor and heat break
https://amzn.to/3kvPem6
— COOLING (Part 3: Video Deep Dive)
4010 blower fans (24V), updated toolhead
https://amzn.to/3irazKT
optimized air ducts for part cooling with aluminium tape insulation
https://amzn.to/3zhbuEs
External Static Cooling: 4x4020 fans (24V)
https://amzn.to/3zcap0D
4x40mm heatsink at AB stepper motors
https://amzn.to/3irvLAh
2x 4020 / or 4010 fans (5V) at heat sinks (stepper motors)
https://amzn.to/3wOmfMJ
25mm axial fan (5V) for stepper drivers
https://amzn.to/3eDf4AW
— Software / Firmware / Controllers (Part 4: Video Deep Dive):
Klipper
https://www.klipper3d.org/
Raspberry Pi Zero W (Mainsail)
https://amzn.to/3xR9l21
Raspberry Pi 3B (Input Shaping and Octoprint)
https://amzn.to/2UwIMAu
Alternative: Raspberry Pi4:
https://amzn.to/3kBt4io
Simplify 3D: multi processes used
https://www.simplify3d.com/
-------------------------------------------------------
My modest video gear*:
iPhone 11 Pro: https://amzn.to/2VZYswJ
Smartphone video rig: https://amzn.to/3iriub5
GoPro Hero 9: https://amzn.to/2UZI9Q5
FLIR ONE PRO: https://amzn.to/2UWAe67
Similar to the soft boxes I use: https://amzn.to/3xRes2d
Similar to the tripod I use: https://amzn.to/2V1I6mw
*Amazon links are affiliate links at no extra costs for you!
#JoinTheSpeed
#247printing
#volcomosq
#SpeedBoatRace
Видео 1000mm/s: RELAXED TESTING канала 247printing
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Bambu's "BIG A1 256³": Reviewed in 59s !New Bambu Lab A1 (not Mini): The bigger Brother in action!Creality K1 MAX vs QIDI X-MAX 3: Tech Review and XXL Comparison!Bambu Lab A1 Mini - Tech ReviewBambu Lab A1 Mini - Overview in 58 seconds! #shortsINSANE PRINT of a COMPLEX PART (2023 edition)1500 mm/s at 70k mm/s² (7.1G) - a FUNCTIONAL PART! (PREVIEW) #shorts247zero BETA2 : MOTION and EXTRUSION - The FASTEST 3D printer ?!WORLD'S FASTEST 3DBENCHY print - 02:25 (mm:ss) on 247zeroB2IMG_2470.MOV #247zero #shortsTORNADO MODE V2: Up to 1650 mm/s INSANE circular movement! #shorts1500 mm/s at 75k mm/s² acc! --247zeroB2-- first SHAKEdown! #shortsThe forgotten BEAST: VORON M4 SHAKEDOWN! #shortsIs BOWDEN DEAD? Direct Drive vs. Bowden DEEP DIVE on Voron Zero!ULTRA lightweight X-BEAMS tested - USELESS on Voron 0.0 / 0.1 / 0.2 ?209h printing! My BIGGEST and LONGEST PRINT (almost FAILED) #shortsOne WEEK PRINT TIME: My BIGGEST Print ! #shortsHOW FAST is NEXT GEN 3D Printing? 247zero revisited!Elegoo Neptune Max is too big ?!The CHEAPEST FASTEST FILAMENT! #shortsIs 247zero too loud? #shorts