Hydraulic Tubing Bender Build
In this video I fabricated a hydraulic/pneumatic tubing bender with the build plans from Takacs Cycles. Here's a link to the plans- http://www.gottrikes.com/Tube_Bender.htm
They're a fantastic deal, very detailed and easy to follow. I used a Bridgeport mill and had access to a lathe to make some bushings, but there is an option to build with or without the turned bushings, so you could easily build this yourself with just a drill press and a way to cut the tubes and flat stock to length.
I knew I was going to need a tubing bender when I got to the suspension components on the Falcon Restomod Project. When I began designing my own bender I came across these plans and figured for less than $20 I couldn't pass it up. The plans utilize readily available materials and parts as well as the Pro-Tools 105 series bending dies, which are a little on the expensive side. My first project was a pair of control arms for my Mustang which I made from 1-1/4", .120 wall DOM. Next up is a roll cage and then I'll be back on the Falcon to make more suspension parts and another roll cage.
I couldn't be happier with the bender. Now I need to slap some paint on it.
MB01SHNAPGZMSOH
Видео Hydraulic Tubing Bender Build канала Bradfords_Garage
They're a fantastic deal, very detailed and easy to follow. I used a Bridgeport mill and had access to a lathe to make some bushings, but there is an option to build with or without the turned bushings, so you could easily build this yourself with just a drill press and a way to cut the tubes and flat stock to length.
I knew I was going to need a tubing bender when I got to the suspension components on the Falcon Restomod Project. When I began designing my own bender I came across these plans and figured for less than $20 I couldn't pass it up. The plans utilize readily available materials and parts as well as the Pro-Tools 105 series bending dies, which are a little on the expensive side. My first project was a pair of control arms for my Mustang which I made from 1-1/4", .120 wall DOM. Next up is a roll cage and then I'll be back on the Falcon to make more suspension parts and another roll cage.
I couldn't be happier with the bender. Now I need to slap some paint on it.
MB01SHNAPGZMSOH
Видео Hydraulic Tubing Bender Build канала Bradfords_Garage
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Custom reamer for fixing my cylinder head cam journals. #4.6 #5.4 #3V](https://i.ytimg.com/vi/1f4qCa1pdC4/default.jpg)
![Waterford Hills OTD | 4.10.22 | 3V Swapped New Edge](https://i.ytimg.com/vi/w6ahs710ZBU/default.jpg)
![Competition Laps- Oct. 11, 2020 Bracket Race Waterford Hills](https://i.ytimg.com/vi/s9TO_4f4dPU/default.jpg)
![Rotisserie Build- 1969 Falcon Restomod](https://i.ytimg.com/vi/Gnoq1HR1z-s/default.jpg)
![Hot Lap PB at Waterford Hills- 1:18.367 | 3V Swapped New Edge](https://i.ytimg.com/vi/AiOfCmSaWF4/default.jpg)
![1969 Falcon Restomod- Update 1- 2.27.2020](https://i.ytimg.com/vi/GtG1G5h90fU/default.jpg)
![Gas Tank Patches](https://i.ytimg.com/vi/dHdNEYrT8yQ/default.jpg)
![Dyno Tuning the Mustang](https://i.ytimg.com/vi/z2mJ8bdpIB4/default.jpg)
![Falcon Build Update- Episode 2](https://i.ytimg.com/vi/saH-jOf9SfE/default.jpg)
![Waterford Hills- Bracket Race | PB 1:18.18 | 3V Swapped New Edge](https://i.ytimg.com/vi/hmdM6ngGZEc/default.jpg)
![3V 4.6 Swap | Longblock Build | Dyno Numbers | Chapter 2, Part 2](https://i.ytimg.com/vi/UiK6lFnzHsw/default.jpg)
![Chapter 1: Porting The Heads | #TrackWorthyNewEdge](https://i.ytimg.com/vi/FWgqaoRNrAo/default.jpg)
![Cylinder Heads Pt 2 | DIY 4 Angle Valve Job | #TrackWorthyNewEdge | Chapter 1, Part 2](https://i.ytimg.com/vi/QFxSCVlL6Uo/default.jpg)
![Modular 4.6 3v Short Block Build | #trackworthynewedge | Chapter 2, Part 1](https://i.ytimg.com/vi/MirOuu7YvWs/default.jpg)
![Falcon Build Update: Episode 3](https://i.ytimg.com/vi/x85I47vW9NQ/default.jpg)
![Introduction- 1969 Ford Falcon Restomod Build](https://i.ytimg.com/vi/AU5Q0BhasDc/default.jpg)