This might work better than I thought // Part 2

Full Color Plans Available Here: https://bit.ly/3HnFDJ7
3D Printed Tools Available: https://bit.ly/3D28ksv

For part 2 of this build series I'm going to pick up where we left off in part 1. The first thing I need to do is install all of the electrical and dust collection components. I'm choosing to do this now while I have easy access inside the dust collection compartment. The added benefit of doing this early is that you can easily use the dust collection part while you're building!

Next up is the top. I'm using the Kreg ACS (Adaptive Cutting System) in this build because I think it packs such a huge punch in a small footprint. It's not cheap so I want to take care of it. The first step to doing that is to seal the MDF top with a 1/2 water 1/2 polycrylic mixture that I've seen others have success with. MDF is THIRSTY! I ended up using 4 coats with a light sanding in between and it could have honestly probably taken 8!

With the top sealed up I mounted it to the workbench which means I can now use it. It took just a minute or two to install the track brackets and get everything squared up. Once it was set up I could start making very accurate, controlled, and even repeatable cuts. What a lifesaver in a small shop! I quickly cut out all of the drawer parts out of 1/2" MDF.

Now it was just a matter of assembling the drawers and installing them in the workbench. I'm really happy with how the plans turned out for this project because it makes this part a breeze! The drawers were all mounted in about 20 minutes, which would normally have taken me 2 hours. After putting on the 2 dust collection compartment doors...I was done! For now...

If you're interested in building one or making your own version, check out the links below for all of the tools and products I used for this build (affiliate links help support the channel!):

Interested in getting the 3D printed parts for this project?: https://etsy.me/36rJK2H
Or, print your own: https://www.thingiverse.com/thing:4391584

Tools:
Plywood Panel Carrier Handle: https://amzn.to/2yzr9Vi
Kreg ACS Plunge Saw: https://amzn.to/2VHRdG0
Kreg ACS Plunge Saw Track (62"): https://amzn.to/2VItllv
Kreg ACS Table Top: https://amzn.to/3bqfNSb
Kreg K5 Pocket Hole Jig: https://amzn.to/2xD6Czo
Rigid Jig-Saw: https://homedepot.sjv.io/3QqBy
Rigid Impact Driver: https://homedepot.sjv.io/dBP23
Klein Wire Cutter/Stripper: https://amzn.to/361uUQp

Cabinet Products:
Friho 16" Full Extension Drawer Slides (5 pair): https://amzn.to/2yDuDa3
2" Desk Cord Grommet: https://amzn.to/2WKAPFc
Surface Mount Face Frame Hinge: https://amzn.to/3cmAOh6
Kreg Pocket Hole Screw Kit: https://amzn.to/3eGYChw
ACS Top Replacement M6 Bolts: https://www.mcmaster.com/90180a612

Dust Collection/Electrical Products:
Yellow Jacket 4-Outlet Power Block: https://amzn.to/3bkRnst
iVac Pro Switch: https://amzn.to/3fJ1j2C
iVac Pro Tool Sensor: https://amzn.to/3fEqovp
Recessed Power Outlet: https://amzn.to/2YTlchm
Retractable Extension Cord Reel: https://amzn.to/2WLTYXd
Plug End Replacements: https://amzn.to/3cxPHwQ
Cable Clamp Assortment Pack: https://amzn.to/3fATAU2
Dust Right Separator: https://amzn.to/34OViw8 3942010
Shop Vac (Thin Profile): https://amzn.to/3cA1ESA
Dust Right Universal Small Hose Kit: https://amzn.to/2RPT0Yg
Powertec 3-tool (2.5") Dust Collection Fittings: https://amzn.to/2Ki5K5O 2.5" Dust Collection Hose (10'): https://amzn.to/2VEJ98Q

Shop Nation Links:
----------------------------------------------------
Shop Nation Website: https://www.shopnationstore.com
Instagram (@dreamshopnation): https://www.instagram.com/dreamshopnation
Timberland Pro: https://bit.ly/ShopNation_TimberlandPro

Thanks for watching!

#workbench #dustcollection #Kreg #workbenchbuild

Видео This might work better than I thought // Part 2 канала Shop Nation