The Making of an Ottertail Paddle

A Quest for an Ottertail Paddle

Canoe paddles come in various shapes and styles. I have used square tip, bent shaft, beavertail, and oversized paddles - but never the Ottertail. My quest for an Ottertail paddle began this summer after I met Dick Perrson of Buckhead Canoe Company in Buckhead, Ontario. Dick was providing me a tour of his workshop/store, when I asked about the thin blade paddle hanging along the wall.

Dick's explanation of the Ottertail caught my attention when he mentioned you could do the J-stroke paddle return without taking the paddle from the water. I have been using the J stoke for the past few years, and his mention of a change in my J-stroke was something I just had to try. Dick shared his use and knowledge of the Ottertail paddle in the video below.

What is an Ottertail Paddle?

The video interview of Dick best describes the use of the Ottertail, but as an introduction here, let me respond to the obvious question, "What is an Ottertail paddle?"

The major distinction between the Ottertail and other paddles is its narrow blade. The Ottertail is most often used from the stern. Its distinctive shape is easier on the shoulder for traveling long distances. The Ottertail is popular with canoeists for lake and flat water travel.

Ottertails come in a variety of shapes and materials. The grip has many styles (Maine Guide, t-grip, standard grip, etc.) The Ottertail blade is thinner than most other paddles. Blades can be straight, wider at the top and narrower at the bottom, and thinner at the top and wider at the bottom. Most blades are rounded at the end and allow the paddle to slice the water easily and gently.

Ottertail Paddle is similar in design to that of the Beaver Tail but has a narrower and rounded blade towards the tip and has a shorter shaft length.

All canoes must be equipped with an extra paddle, so why not carry an Ottertail for the long trip on flat water. When in whitewater or needing speed to return back to camp for dinner or get out of a coming storm, grab the beavertail or square tail paddle.

A Custom Made Ottertail Paddle

My next step was to try an Ottertail paddle. Interestingly, none of my paddling buddies had an Ottertail, so I turned to my cousin Linwood, a Master Maine Guide. He located a paddle maker, Dri-Ki Woodworking, in nearby Patten, Maine where I could have my own Ottertail paddle built specifically for me. An exchange of emails with Linwood and owner Rick Keim, led to my visit to Dri-Ki Woodworking to watch the Ottertail paddle being made. Rick not only gave me a tour of his shop, but he said, "Let me build an Ottertail for you". The below video shows craftsman/artist/Rick going through the various processes required to build my custom paddle. Rick buys the white ash logs with a beautiful grain and strong wood. Rick dries and mills the logs himself, then uses the outer part of the log, the straightest grain, for the paddle. The paddle is outlined in pencil on a blank, and then a band saw is used to rough cut the paddle. Then a variety of planer and sawing equipment is used to obtain the Ottertail shape. Once Rick is comfortable with the paddle, it receives two separate polyurethane dips.

There are various ways to determine the length of an Ottertail paddle. The method we used was to measure from the floor to the bottom of my chin.

References
• Trent-Severn Waterway Special Memories of Buckhorn Canoe Company http://www.youtube.com/watch?v=hls_rhMn7Gw
• Dri-Ki Woodworking http://dri-kiwoodworking.com/
• OutdoorSteve.com http://www.outdoorsteve.com
• Loons Nest http://www.loonsnest.biz
• Paddling.Net: Up the Creek with the Right Paddle
http://www.paddling.net/guidelines/showArticle.html?171

Видео The Making of an Ottertail Paddle канала Stephen Priest