Leela - The ESPHome Room Multi Sensor for Home Assistant
Leela is a 3D printable sensor housing intended to be used with Home Assistant and ESPHome. She can be described as a "room sensor" with the primary sensors being motion, temperature and humidity. The data from these sensors can be very useful in Home Assistant and of course can be used to power automations such as turning on/off lights, heating, extractor fans... and all the other amazing things HA can do!
Leela is designed to be:
1. Simple to print and setup.
2. Provide reliable and accurate data
3. Be modular and compatible with a wide range of readily availble ESP boards and sensors
4. Offer value for money that cannot be matched by off the shelf branded products
5. Pass "The Wife Test" and not look like a piece of garbage stuck together with Ducktape and Hot Glue.
The entire enclosure can be printed in one go on a Prusa i3 sized printer (and probably smaller) but is split into three seperate files for flexibility (print front and back in contrasting colours for instance) The free version of Leela with simple stand only uses 69g of filament while the optional flexible stand/wallmount add another 40g. Only one area requires a very small amount of support material.
Leela is launching with support for two commonly used ESP boards, PIR motion sensor and temperature/humidity sensor. Support for an mmWave presence sensor and alternate temperature sensors will also be released in the near future.
Assuming you have a spare USB power supply and USB cable laying around, the cost for electronics within this intial version of Leela can be as low as 5 Dollars/Euros/Pounds (even lower with a future temperature sensor) Factoring in the cost of filament used to print Leela and the total cost of assembly can be under 7 Dollars/Euros/Pounds.
Leela doesn't look like hot junk and should look at home on a shelf or mounted to a wall. The design should ensure you will still get snu snu if you have a significant other.
Leela has now launched on Printables, download her today for free:
https://www.printables.com/model/713218
Видео Leela - The ESPHome Room Multi Sensor for Home Assistant канала zerofox3D
Leela is designed to be:
1. Simple to print and setup.
2. Provide reliable and accurate data
3. Be modular and compatible with a wide range of readily availble ESP boards and sensors
4. Offer value for money that cannot be matched by off the shelf branded products
5. Pass "The Wife Test" and not look like a piece of garbage stuck together with Ducktape and Hot Glue.
The entire enclosure can be printed in one go on a Prusa i3 sized printer (and probably smaller) but is split into three seperate files for flexibility (print front and back in contrasting colours for instance) The free version of Leela with simple stand only uses 69g of filament while the optional flexible stand/wallmount add another 40g. Only one area requires a very small amount of support material.
Leela is launching with support for two commonly used ESP boards, PIR motion sensor and temperature/humidity sensor. Support for an mmWave presence sensor and alternate temperature sensors will also be released in the near future.
Assuming you have a spare USB power supply and USB cable laying around, the cost for electronics within this intial version of Leela can be as low as 5 Dollars/Euros/Pounds (even lower with a future temperature sensor) Factoring in the cost of filament used to print Leela and the total cost of assembly can be under 7 Dollars/Euros/Pounds.
Leela doesn't look like hot junk and should look at home on a shelf or mounted to a wall. The design should ensure you will still get snu snu if you have a significant other.
Leela has now launched on Printables, download her today for free:
https://www.printables.com/model/713218
Видео Leela - The ESPHome Room Multi Sensor for Home Assistant канала zerofox3D
Комментарии отсутствуют
Информация о видео
8 января 2024 г. 16:45:29
00:06:23
Другие видео канала
