RHCSA RHEL 8 - Configure firewall settings using firewall-cmd/firewalld
Your support on Ko-Fi is much appreciated:
👉 https://ko-fi.com/csg_yt
Join our new discord channel:
👉 https://discord.gg/kBQ6Jry
Buy CSG Merchandise:
👉 http://tee.pub/lic/csg
This video is based on RHEL 8.
Video to cover the section 'Configure firewall settings using firewall-cmd/firewalld' for the RHCSA (Red Hat Certified System Administrator).
More information on the required learning: http://bit.ly/rhcsa8
Notes from the video:
The local firewall on the server is managed by the firewall-cmd command line, the first area to learn is about zoning on the firewall.
This has been covered largely in a previous video though some sections will be revisited.
Note in the exam you may be asked to enable IP forwarding this essentially allows the server to route packets to do this you need to enable it in the sysctl file:
# vi /etc/sysctl.conf
Add the following line:
# net.ipv4.ip_forward=1
Then to ask sysctl to re-read the config:
# sysctl -p
I will mostly go over the same using the GUI, to launch to GUI run:
# firewall-config
Note, this won’t be installed by default, to install run:
# dnf install firewall-config
To get the current state of the firewall run:
# firewall-cmd --state
To list all of the zones run:
# firewall-cmd --get-zones
To see what is configured in a particular zone:
# firewall-cmd --zone servers --list-all
To view the zones currently assigned to each interface, use the –get-active-zones option:
# firewall-cmd --get-active-zones
To get the current config of a particular zone:
# firewall-cmd --zone servers --list-all
#rhcsa #rhel #linux #redhat
Видео RHCSA RHEL 8 - Configure firewall settings using firewall-cmd/firewalld канала Computers, Security & Gadgets
👉 https://ko-fi.com/csg_yt
Join our new discord channel:
👉 https://discord.gg/kBQ6Jry
Buy CSG Merchandise:
👉 http://tee.pub/lic/csg
This video is based on RHEL 8.
Video to cover the section 'Configure firewall settings using firewall-cmd/firewalld' for the RHCSA (Red Hat Certified System Administrator).
More information on the required learning: http://bit.ly/rhcsa8
Notes from the video:
The local firewall on the server is managed by the firewall-cmd command line, the first area to learn is about zoning on the firewall.
This has been covered largely in a previous video though some sections will be revisited.
Note in the exam you may be asked to enable IP forwarding this essentially allows the server to route packets to do this you need to enable it in the sysctl file:
# vi /etc/sysctl.conf
Add the following line:
# net.ipv4.ip_forward=1
Then to ask sysctl to re-read the config:
# sysctl -p
I will mostly go over the same using the GUI, to launch to GUI run:
# firewall-config
Note, this won’t be installed by default, to install run:
# dnf install firewall-config
To get the current state of the firewall run:
# firewall-cmd --state
To list all of the zones run:
# firewall-cmd --get-zones
To see what is configured in a particular zone:
# firewall-cmd --zone servers --list-all
To view the zones currently assigned to each interface, use the –get-active-zones option:
# firewall-cmd --get-active-zones
To get the current config of a particular zone:
# firewall-cmd --zone servers --list-all
#rhcsa #rhel #linux #redhat
Видео RHCSA RHEL 8 - Configure firewall settings using firewall-cmd/firewalld канала Computers, Security & Gadgets
Показать
Комментарии отсутствуют
Информация о видео
18 июля 2020 г. 19:45:43
00:18:27
Другие видео канала
![RHCSA RHEL 8 - Restrict network access using firewall-cmd/firewall](https://i.ytimg.com/vi/ZNmTKAdDnrc/default.jpg)
![RHCSA v8 Practice Session: Configure key-based authentication for SSH](https://i.ytimg.com/vi/P_GxqUjQ8MY/default.jpg)
![Demystifying firewalld](https://i.ytimg.com/vi/a6EUoDNMnHA/default.jpg)
![What is a Firewall?](https://i.ytimg.com/vi/kDEX1HXybrU/default.jpg)
![](https://i.ytimg.com/vi/TlLWK-dGd_A/default.jpg)
![RHCSA | LOG MANAGEMENT - How to configure rsyslog in redhat linux | Tamil](https://i.ytimg.com/vi/fQpRNeqhNG0/default.jpg)
![RHCE Training - Configuring Firewalld in RHEL 7](https://i.ytimg.com/vi/jgErVHBz7XI/default.jpg)
![RHCSA v8 Practice Session: Configure firewall settings using firewall-cmd/firewalld](https://i.ytimg.com/vi/CwPiFiXdd98/default.jpg)
![RHCSA RHEL 8 - Create and use file access control lists](https://i.ytimg.com/vi/MWziVT0MrBU/default.jpg)
![CentOS 7: Firewalld Concepts and Examples [RHCSA7/RHCE7]](https://i.ytimg.com/vi/TyMallqnWiw/default.jpg)
![Linux Pluggable Authentication Modules (PAM)](https://i.ytimg.com/vi/uebQr2KvQzA/default.jpg)
![Linux Firewall Tutorial | How to Configure Firewall Rules with UFW](https://i.ytimg.com/vi/XtRXm4FFK7Q/default.jpg)
![Domain Name Server (DNS) Configuration in Redhat Enterprise Linux 7/8](https://i.ytimg.com/vi/enE1m3mv_IY/default.jpg)
![Samba Share Configuration || Red Hat Enterprise Linux 8](https://i.ytimg.com/vi/Cjrpq63xaHQ/default.jpg)
![RHCSA v8 Practice Session: Processing shell command exit codes](https://i.ytimg.com/vi/3aklR-mXTTg/default.jpg)
![Managing firewalld using firewall-cmd command [RHEL-7.3]](https://i.ytimg.com/vi/sA_MBFD-gLA/default.jpg)
![Advanced Linux firewall config. with firewalld rich rules and IPset - rich rules + ipset](https://i.ytimg.com/vi/tt2-M8CVgx4/default.jpg)
![RHCSA v8 Practice Session: Process script inputs ($1, $2, etc.)](https://i.ytimg.com/vi/H51D2E4vHwY/default.jpg)
![RHEL8 Hindi Tutorials for Configuring Firewall-cmd Command with Port & Service Filtering in Linux](https://i.ytimg.com/vi/EC6tU-kEoN0/default.jpg)
![RHCSA RHEL 8 - Restore default file contexts](https://i.ytimg.com/vi/jvru7ioRAkU/default.jpg)