New Odroid N2L Review - Amazing for Emulation - Gamester81

I review the new N2L single board computer by Odroid. It's reasonably priced, and comparable to the Raspberry Pi 4. This is using the EmuELEC 4.6+ build.

Available at: https://www.hardkernel.com/shop/odroid-n2l-with-4gbyte-ram/

Qbertaddict1's YouTube Channel: https://www.youtube.com/@qbertaddict1

Odroid N2L Specs:

Form Factor: Dimensions including Fan heatsink: 69mm x 56mm x 22mm
Dimensions including Tall heatsink: 69mm x 56mm x 32mm
Weight: 50g including Fan heatsink, 66g including Tall heatsink

Processor: Amlogic S922X Processor (12nm)
Quad-core Cortex-A73(2.2Ghz) and Dual-core Cortex-A53(2Ghz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G52 GPU with 6 x Execution Engines (800Mhz)

Memory: LPDDR4 4GiB or 2GiB with 32-bit bus width
Data rate: 3216 MT/s
1.1Volt low power design

Storage: 1 x eMMC connector (8G, 16G, 32G, 64G and 128G are available)
1 x microSD slot (DS/HS modes up to UHS-I SDR104)

Networking: Optional WiFi or Ethernet USB adapters
Video 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)
– Although the +5V Power pin is able to supply a minimum of 300mA, according to HDMI 2.0 specification, a sink shall not draw more than 50mA of current from the +5V Power pin.

Audio: 1 x HDMI digital output
External I/O 1 x USB 3.0 Host port
1 x USB 2.0 Host port
1 x Debug serial console (UART)
1 x MIPI DSI 4Lane (TBD)
1 x Peripheral Expansion Header (40-pin, 2.54mm pitch)
– 2 x DC 5V, 2 x DC 3.3V, 1 x DC 1.8V, 8 x GND
– 1 x SPI
– 1 x UART
– 2 x I2C
– 25 x GPIO (Max)
– 2 x ADC input (10bit, 1.8V Max)
– All of I/O signal level is 3.3 Volt except for ADC input at max 1.8 Volt

Other features: Built with a large passive heatsink
System LEDS Indicators:
– Red (PWR) – Solid light when DC power is connected
– Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
Active Cooling Fan Connector (5V 2-pin)
– Connector (2-pin, 1.25mm pitch)

Power: 1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm
7.5V ~ 16V (Recommend range of input)
– DC 12V/2A power adapter is recommendedPower consumption:
– IDLE : ≃ 1.5W (Performance governor), 1.3W(Conservative governor)
– CPU Stress (Passive Heat-Sink) : ≃ 5.4W (@1908/2208MHz, Stock), 5.8W (@2016/2400MHz, Overclock)
– CPU Stress (Active Cooling-FAN) : ≃ 6.1W (@1908/2208MHz, Stock), 6.4W (@2016/2400MHz, Overclock)
– Power-Off : ≃ 0.2W

Raspberry Pi 4 Specs:

Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
1GB, 2GB, 4GB or 8GB LPDDR4-3200 SDRAM (depending on model)
2.4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE
Gigabit Ethernet
2 USB 3.0 ports; 2 USB 2.0 ports.
Raspberry Pi standard 40 pin GPIO header (fully backwards compatible with previous boards)
2 × micro-HDMI ports (up to 4kp60 supported)
2-lane MIPI DSI display port
2-lane MIPI CSI camera port
4-pole stereo audio and composite video port
H.265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode)
OpenGL ES 3.1, Vulkan 1.0
Micro-SD card slot for loading operating system and data storage
5V DC via USB-C connector (minimum 3A*)
5V DC via GPIO header (minimum 3A*)
Power over Ethernet (PoE) enabled (requires separate PoE HAT)
Operating temperature: 0 – 50 degrees C ambient

More at: http://gamester81.com/

Follow me at:
Facebook: https://www.facebook.com/Gamester81Fanpage
Twitter: https://twitter.com/gamester81
Instagram: http://instagram.com/gamester81

My other channels:
Starwarsnut77: https://www.youtube.com/user/starwarsnut77
NEStalgiaholic: https://www.youtube.com/user/NEStalgiaholic

Видео New Odroid N2L Review - Amazing for Emulation - Gamester81 канала Gamester81