Repair P0301 Misfire P0171 Lean Toyota Camry √ Fix it Angel

Daily Deals on Government Auctions https://tinyurl.com/y384vdr2 https://tinyurl.com/ydb3nufu
https://tinyurl.com/yyx4fa92 https://www.amazon.com/shop/fixitangel i get a commission on products purchased through links in my video description
1996 1997 1998 1999 2000 2001 Toyota Camry, 4 cylinders, 5S-FE, 2.2 Liter

Fuel Injector https://amzn.to/2Jxrf3e
https://tinyurl.com/y4zbveu5
Valve Cover Gasket https://amzn.to/2VxlMkf
https://tinyurl.com/y23bk84y
Scan tool https://amzn.to/2LxHPCV
https://tinyurl.com/yxk6trcj
Pliers https://goo.gl/wBSjlw
https://goo.gl/XK5qpX
1/2" Dr. Large Metric Socket Set https://amzn.to/2E1MXsR
https://tinyurl.com/y46tog3v
1/2 Drive Ratchet https://goo.gl/yY9aKo
https://goo.gl/DNoQij
12 pc. Ratcheting Wrench Set https://goo.gl/CrgwBN
https://goo.gl/3JKHGz
Digital Volt Ohm Meter https://goo.gl/BzmLgq
https://goo.gl/ATBqDj
Shop Towels https://goo.gl/K1LJKh
https://goo.gl/aeqBTL
Shop Rags https://goo.gl/wzFLHT
https://goo.gl/C6UfjR

2000 Toyota Camry
Diagnosed #1 injector on cylinder #1 was bad. High resistance on the injector causing rough idle. Replaced it with Genuine Toyota injector.

P0301, P0302, P0303 and P0304:
Misfiring of random cylinders is detected in any particular 200 or 1000 revolutions.
For any particular 200 revolutions for engine, misfiring is detected which can cause catalyst over heating (this will cause MIL to blink)

Possible Trouble Areas:

-Open or short in engine wire
-Connector connection
-Vacuum hose connection
-Ignition system
-Injector
-Fuel pressure
-EGR system
-Manifold Absolute Pressure sensor (MAP)
-Engine Coolant Temperature sensor (ECT)
-Compression pressure
-Valve clearance
-Valve timing
-ECM (Engine Control Module)

P0171:
When air-fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on RICH side (2 trip detection logic)

Possible Trouble Areas:

-Air induction system
-Injector bad or blockage
-Manifold Absolute Pressure
-Engine coolant Temperature sensor
-Fuel pressure
-Gas leakage on exhaust
-open or short in heated oxygen sensor (bank 1 sensor 1) circuit
-Heated oxygen sensor (bank 1 sensor 1)
-ECM

Conclusion:
I replaced the fuel injector because of blockage of fuel causing a misfire, lean condition at cylinder #1. The PCV and rubber grommet was also replaced since it was never been changed. A bad PCV may cause a rough idle, hard starting and/or lean misfire (which increases emissions and wastes fuel).

The information contained in this video is for general guidance, not responsible for any errors or injuries that you have done. Samsung W200 pocket camcorder was used to do this video.

Please subscribe and thank you for watching.
Follow me on TWITTER: @88bmyvegas and http://lasvegasautoinsider.blogspot.com/ DISCLAIMER - Due to factors beyond the control of FixitAngel, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. FixitAngel assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. FixitAngel recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of FixitAngel, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not FixitAngel nor any of it’s subsidiaries.

Видео Repair P0301 Misfire P0171 Lean Toyota Camry √ Fix it Angel канала Fix It Angel