300 PRC Custom Build: Chambering and Machining the Barrel
Full Story: https://ultimatereloader.com/2019/09/13/300-prc-custom-build-chambering-and-machining-the-barrel/
Gordy Gritters / Fred Zeglin Book: https://amzn.to/34HDe6D
UR T-Shirts: https://bit.ly/2UEAkgW
UR on Patreon: https://www.patreon.com/ultimatereloader
Important notes:
- See chapter markers below
- This is a high-level overview for this particular project
- I am not teaching lathe operation in this video (see Making with Metal videos for that)
- There are 6 rifle chambering projects in the hopper, will be showing different things each time.
- Future videos will break down each process for chambering a rifle (individual stories)
0:10 Introduction, resources, background
4:00 Outline of components and process
6:20 Cutting down barrel blank (breech end)
7:00 Initial dial-in, facing, pre-drilling
8:18 New barrel dial-in technique
10:26 Dave Manson reamer, bushings, Go/No-Go gauges
10:57 Boring pre-drill, checking for runout
11:36 Turning tenon
12:54 Cutting threading relief
13:49 Threading the tenon
15:35 Checking for thread fit
15:57 Indexing barrel and action (barrel internal curvature)
20:17 Finished tenon, chambering setup
21:13 Precision Matthews PM-1440GT lathe performance/alignment
21:33 Pressure flush -vs- manual flush reaming
22:05 Viper's Vennom oil, starting chambering
23:18 Hawkeye Borescope - inspecting chambering progress
24:25 Monitoring chambering depth
24:48 Final chambering cuts and checks (last 0.010")
25:17 0.002" Go Gauge shim (tape)
26:43 Chamfering the chamber opening, polishing the chamber
27:44 Cutting barrel down (muzzle end)
28:04 Muzzle threading quick overview
29:48 Installing barrel
32:21 Checking headspace
33:33 Conclusion
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Disclaimer:
You alone are responsible for the safety of yourself and your property.
Check local and state laws before undertaking any activity involving possessing, transporting, and shooting firearms. Check local and state laws before attempting to load ammunition or perform any modifications to a firearm. Always abide by the law. Always practice gun safety.
The content on this channel (including videos, ammunition reloading data, technical data, comments, and any other information contained within) is for demonstration purposes only.
Do not attempt any of the processes or procedures shown or described in this video or on this YouTube channel (gavintoobe).
Any reloading data supplied on this YouTube channel (gavintoobe) or in this video, including any comments from viewers and readers must be assumed to be in error.
Always consult at least three sources of manufacturer's ammunition reloading data before reloading your own ammunition.
Do not attempt to repair or modify any firearms based on information found on this YouTube channel or in this video.
Gunsmithing procedures should only be performed only by a licensed gunsmith.
Ultimate Reloader, LLC can not be held liable for any harm caused to any individual or any personal property related to activities, procedures, techniques, or practices described in whole or part on this YouTube channel (gavintoobe) or in this video.
By watching this video in whole or in part, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this YouTube channel (gavintoobe) or in this video.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Material Connection Notice:
The following Ultimate Reloader partners are featured in this video:
- Hornady
- Benchmark Barrels
- TriggerTech
- MDT
Ultimate Reloader partnerships involve one or more of the following:
Product supplied for evaluation + testing + features in videos/articles, paid advertising and promotions, engineering and product development services, scientific testing and evaluation, external media production and related marketing services.
Ultimate Reloader LLC is committed to publishing subjective and data-driven information+insights related to products whether it be favorable or unfavorable or both.
For more information about Ultimate Reloader partnerships, please visit: https://ultimatereloader.com/about
Видео 300 PRC Custom Build: Chambering and Machining the Barrel канала gavintoobe
Gordy Gritters / Fred Zeglin Book: https://amzn.to/34HDe6D
UR T-Shirts: https://bit.ly/2UEAkgW
UR on Patreon: https://www.patreon.com/ultimatereloader
Important notes:
- See chapter markers below
- This is a high-level overview for this particular project
- I am not teaching lathe operation in this video (see Making with Metal videos for that)
- There are 6 rifle chambering projects in the hopper, will be showing different things each time.
- Future videos will break down each process for chambering a rifle (individual stories)
0:10 Introduction, resources, background
4:00 Outline of components and process
6:20 Cutting down barrel blank (breech end)
7:00 Initial dial-in, facing, pre-drilling
8:18 New barrel dial-in technique
10:26 Dave Manson reamer, bushings, Go/No-Go gauges
10:57 Boring pre-drill, checking for runout
11:36 Turning tenon
12:54 Cutting threading relief
13:49 Threading the tenon
15:35 Checking for thread fit
15:57 Indexing barrel and action (barrel internal curvature)
20:17 Finished tenon, chambering setup
21:13 Precision Matthews PM-1440GT lathe performance/alignment
21:33 Pressure flush -vs- manual flush reaming
22:05 Viper's Vennom oil, starting chambering
23:18 Hawkeye Borescope - inspecting chambering progress
24:25 Monitoring chambering depth
24:48 Final chambering cuts and checks (last 0.010")
25:17 0.002" Go Gauge shim (tape)
26:43 Chamfering the chamber opening, polishing the chamber
27:44 Cutting barrel down (muzzle end)
28:04 Muzzle threading quick overview
29:48 Installing barrel
32:21 Checking headspace
33:33 Conclusion
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Disclaimer:
You alone are responsible for the safety of yourself and your property.
Check local and state laws before undertaking any activity involving possessing, transporting, and shooting firearms. Check local and state laws before attempting to load ammunition or perform any modifications to a firearm. Always abide by the law. Always practice gun safety.
The content on this channel (including videos, ammunition reloading data, technical data, comments, and any other information contained within) is for demonstration purposes only.
Do not attempt any of the processes or procedures shown or described in this video or on this YouTube channel (gavintoobe).
Any reloading data supplied on this YouTube channel (gavintoobe) or in this video, including any comments from viewers and readers must be assumed to be in error.
Always consult at least three sources of manufacturer's ammunition reloading data before reloading your own ammunition.
Do not attempt to repair or modify any firearms based on information found on this YouTube channel or in this video.
Gunsmithing procedures should only be performed only by a licensed gunsmith.
Ultimate Reloader, LLC can not be held liable for any harm caused to any individual or any personal property related to activities, procedures, techniques, or practices described in whole or part on this YouTube channel (gavintoobe) or in this video.
By watching this video in whole or in part, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this YouTube channel (gavintoobe) or in this video.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Material Connection Notice:
The following Ultimate Reloader partners are featured in this video:
- Hornady
- Benchmark Barrels
- TriggerTech
- MDT
Ultimate Reloader partnerships involve one or more of the following:
Product supplied for evaluation + testing + features in videos/articles, paid advertising and promotions, engineering and product development services, scientific testing and evaluation, external media production and related marketing services.
Ultimate Reloader LLC is committed to publishing subjective and data-driven information+insights related to products whether it be favorable or unfavorable or both.
For more information about Ultimate Reloader partnerships, please visit: https://ultimatereloader.com/about
Видео 300 PRC Custom Build: Chambering and Machining the Barrel канала gavintoobe
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![300 PRC Custom Build: Optics and First Range Trip](https://i.ytimg.com/vi/BJqXPjJ3tgI/default.jpg)
![Rifle Accuracy Factors: A Discussion with Gordy Gritters](https://i.ytimg.com/vi/qZPVAGZrkHo/default.jpg)
![Chambering](https://i.ytimg.com/vi/9OW18sYyfjc/default.jpg)
![Precision Matthews PM-1440GT Lathe In-Depth Walkthrough and Demo](https://i.ytimg.com/vi/Ur8I8nPG0Ko/default.jpg)
![Machining Angled Bosses on The Mill and Lathe](https://i.ytimg.com/vi/eSeYUxV1A4Y/default.jpg)
![300 PRC Budget Build part 1: Action Blueprinting](https://i.ytimg.com/vi/r1UdDrpGvsQ/default.jpg)
![Chambering a new barrel for the wife's rifle (PT 2). 6.5 Creedmoor](https://i.ytimg.com/vi/9nfaFBdTyL4/default.jpg)
![6x47 Lapua Match custom chambering](https://i.ytimg.com/vi/g16JBUR11jQ/default.jpg)
![Meet Gordy Gritters: Record-Setting Master Gunsmith, In-Depth Discussion](https://i.ytimg.com/vi/wKqJ6-ocTBc/default.jpg)
![How a Rifle is Made | Hands-on Tour of the Sako & Tikka Firearms Factory](https://i.ytimg.com/vi/5GVNo3OVwTE/default.jpg)
![Chambering A Proof Research Barrel to an Accurized Remington 700 Receiver | Gunsmithing](https://i.ytimg.com/vi/XCRDQ_yU-HM/default.jpg)
![Making an OAL Gauge Modified Case (300 PRC Demo)](https://i.ytimg.com/vi/rAkbuJk6qQE/default.jpg)
![Home Shop Machinist Tour: Stefan Gotteswinter!](https://i.ytimg.com/vi/H-Sf7Nvkwzg/default.jpg)
![Setting up a gun barrel in the lathe](https://i.ytimg.com/vi/qNCH2FvYcQg/default.jpg)
![Frankford Arsenal Universal Precision Case Trimmer](https://i.ytimg.com/vi/zNrEf0PbiiQ/default.jpg)
![Gavin's First PRS Match: The Gear](https://i.ytimg.com/vi/YC9FiBhWP5M/default.jpg)
![Crowning and Threading barrels the correct way](https://i.ytimg.com/vi/NBVV1Cgy4f8/default.jpg)
![Live Pilot Reamer and Indicating Rod and Bushings by PTG](https://i.ytimg.com/vi/DwyjNOZJsok/default.jpg)
![Thread Depth, Tool Tip Width and Length of Cut NO TRIG NEEDED](https://i.ytimg.com/vi/nLHXSXzQP3U/default.jpg)
![How It's Made: Bat Custom Rifle Actions](https://i.ytimg.com/vi/VkvFtlTEuSc/default.jpg)