DSG 7 (0AM) Basic Settings Procedure
DSG 7 (0AM) Basic Settings Procedure
Prerequisites:
No Fault Codes stored in the TCM
Temperature 30°C - 60°C. The Measuring Block value for G510 is found in group 011.1
Selector Lever in P
Ignition ON, Engine OFF
Parking brake applied
Brake Pedal operated (hold for the whole procedure)
Throttle Pedal not operated
See the Special Notes if the Mechatronic unit needs to be replaced.
[Select]
[02-Transmission]
[Basic Settings - 04]
Group 060
[Go!]
[ON/OFF/Next] may be necessary
The live data should display 4 | 0 | 0 in Basic Settings. This may take up to 2 -to- 5 minutes.
After the 4 | 0 | 0 results are displayed, start the engine immediately and allow it to idle. If 4 | 0 | 0 is not shown do NOT start the engine, something is wrong with the procedure or the transmission.
It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises. This is similar to the 02E 6-Speed DSG.
The live data should display 254 | 0 | 0 to confirm a successful Basic Settings after 3 -to- 6 minutes.
254 | 7 | 0 alone would Not be complete yet and 255 | 0 | 0 would indicate the basic settings was interrupted or failed.
[Done, Go Back]
Switch off Ignition, wait for a few seconds and switch it back on.
[Fault Codes - 02]
Check and clear any fault codes.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive below.
Defined Test Drive
Suggested test drive after replacing the Mechatronics module/TCM or successful basic setting.
With the shifter in Drive accelerate at half throttle to 2nd gear.
Stop and repeat half throttle acceleration into 2nd gear.
Stop followed by shifting into reverse and backing up two times.
Stop followed by driving in each forward gear using the Tiptronic shifters for no less than 3 seconds per gear.
The next portion of the drive must be done in any group choice of the following gears to maintain the proper RPM and maintain a safe driving distance on the road:
A = Gears 4th or 6th (4th is preferred)
B = Gears 3rd, 5th or 7th (5th is preferred)
For those who can support financially:
WebMoney :
E285823852236 Z351298899612 R292943507988 X547004962227
Paypal: eriksonas1975@gmail.com
Видео DSG 7 (0AM) Basic Settings Procedure канала EriksonasTV
Prerequisites:
No Fault Codes stored in the TCM
Temperature 30°C - 60°C. The Measuring Block value for G510 is found in group 011.1
Selector Lever in P
Ignition ON, Engine OFF
Parking brake applied
Brake Pedal operated (hold for the whole procedure)
Throttle Pedal not operated
See the Special Notes if the Mechatronic unit needs to be replaced.
[Select]
[02-Transmission]
[Basic Settings - 04]
Group 060
[Go!]
[ON/OFF/Next] may be necessary
The live data should display 4 | 0 | 0 in Basic Settings. This may take up to 2 -to- 5 minutes.
After the 4 | 0 | 0 results are displayed, start the engine immediately and allow it to idle. If 4 | 0 | 0 is not shown do NOT start the engine, something is wrong with the procedure or the transmission.
It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises. This is similar to the 02E 6-Speed DSG.
The live data should display 254 | 0 | 0 to confirm a successful Basic Settings after 3 -to- 6 minutes.
254 | 7 | 0 alone would Not be complete yet and 255 | 0 | 0 would indicate the basic settings was interrupted or failed.
[Done, Go Back]
Switch off Ignition, wait for a few seconds and switch it back on.
[Fault Codes - 02]
Check and clear any fault codes.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive below.
Defined Test Drive
Suggested test drive after replacing the Mechatronics module/TCM or successful basic setting.
With the shifter in Drive accelerate at half throttle to 2nd gear.
Stop and repeat half throttle acceleration into 2nd gear.
Stop followed by shifting into reverse and backing up two times.
Stop followed by driving in each forward gear using the Tiptronic shifters for no less than 3 seconds per gear.
The next portion of the drive must be done in any group choice of the following gears to maintain the proper RPM and maintain a safe driving distance on the road:
A = Gears 4th or 6th (4th is preferred)
B = Gears 3rd, 5th or 7th (5th is preferred)
For those who can support financially:
WebMoney :
E285823852236 Z351298899612 R292943507988 X547004962227
Paypal: eriksonas1975@gmail.com
Видео DSG 7 (0AM) Basic Settings Procedure канала EriksonasTV
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Inside the VW Golf MK6 DSG 7 speed mechatronicsDSG BASIC SETTINGS Polo golf skoda audi Dsg gearbox Mechatronic unit reset Adaptation P17BF P189C7 speed DSG (0AM,0CW) Basic setting by ODIS ,VOLKSWAGEN , SEAT , SKODA , AUDIDL501 Clutch Adaptation Procedure. S-Tronic, Audi S6, S7, A7, A6, 3.0t, 4.0tHow VW Parts Fail ~ 7 speed DSG Mechatronic Unit7-speed DSG Service MK7.5 VW Golf R - HINT: It's different than the MK7 process!How to Factory Reset DSG Automatic Gearbox || A Must Do For a Used Car!DSG Transmission - ExplainedDSG Basic SettingReemplazando Mecatronica 0AM DSG 7 Vel. 0AM927769DAudi DL501 / S-Tronic *Adaptation/Calibration*2011 GTI DSG mechatronic replacement with a surprise7 speed gearbox DSG / 0AM bassic settingsHow To Fix Engine Hesitation During Acceleration - Easy Fix!Unlock VW and AUDI features easily! OBDeleven Pro Review; VCDS alternative - Netcruzer TECH7 Things You Should NEVER Do In a Manual Transmission Car!Re-calibrating a VW DSG Gearbox using ODISDSG Kupplung einmessen7 DSG (0CW) Basic setting by VCDS ,VOLKSWAGEN , SEAT , SKODA , AUDI, GOLF 7 , AUDI A3.A45 Things You Should Never Do In A Dual Clutch Transmission Vehicle