FlySky i6 Center/EndPoint adjustment for CleanFlight/BaseFlight Example
This is designed to help FlySky i6 owners but may be applied to T6 as well. If you have a T6 please confirm in the comments.
Clarifications:
Enter these CLI commands:
Set Min_Throttle = 1100
Set Max_Throttle =1900
Save
These are the numbers your sliders need to be adjusted to on CleanFlight using your Tx SubTrim and Endpoint menu options while the quad is plugged in to the computer and the flight battery is plugged in. TAKE OFF THE PROPS!!!!!!!!!
Then make sure everything falls withing these numbers.
If a channel is moving backwards in cleanflight then reverse it.
Center points are 1500
Low End point (Left, Down) is 1100 or less
High End point (Right, Up) 1900 or more
I say or Less or More because the number wont land dead on 1100, or 1900 and it needs to be Under 1100 barely and Over 1900 slightly.
Endpoint and center point adjustments for FlySky i6/T6 but the principles are the same for all Tx's just the menu has them listed in a different location than shown in this video and possibly under a different name in the Tx menu.
Leave me comment if you dont understand or Email me at DriveFlyRC@gmail.com
Видео FlySky i6 Center/EndPoint adjustment for CleanFlight/BaseFlight Example канала DriveFlyRC CustomerSupport
Clarifications:
Enter these CLI commands:
Set Min_Throttle = 1100
Set Max_Throttle =1900
Save
These are the numbers your sliders need to be adjusted to on CleanFlight using your Tx SubTrim and Endpoint menu options while the quad is plugged in to the computer and the flight battery is plugged in. TAKE OFF THE PROPS!!!!!!!!!
Then make sure everything falls withing these numbers.
If a channel is moving backwards in cleanflight then reverse it.
Center points are 1500
Low End point (Left, Down) is 1100 or less
High End point (Right, Up) 1900 or more
I say or Less or More because the number wont land dead on 1100, or 1900 and it needs to be Under 1100 barely and Over 1900 slightly.
Endpoint and center point adjustments for FlySky i6/T6 but the principles are the same for all Tx's just the menu has them listed in a different location than shown in this video and possibly under a different name in the Tx menu.
Leave me comment if you dont understand or Email me at DriveFlyRC@gmail.com
Видео FlySky i6 Center/EndPoint adjustment for CleanFlight/BaseFlight Example канала DriveFlyRC CustomerSupport
Показать
Комментарии отсутствуют
Информация о видео
8 августа 2015 г. 4:21:37
00:08:02
Другие видео канала
How to Limit Throttle on FS-i6X - Reduce Throttle Output with Throttle Curve - Flysky i6X i6FlySky FS-i6 Radio Review & Setting up the Radio for a Flying WingHow To Install (RC) Radio Control Systems, Motor, ESC, Servo. Brushed & BrushlessFlySKY i6 Differential Thrust MixFlysky fsi6 3-mode switch setup | Flight Modes setup in mission planner [Altitude hold,RTL,flip]FlySky FS-i6 Betaflight Setup: Calibrating Endpointsflysky fs -i6 modifying battery, gimbal self centering and antennasSetting Subtrim & Endpoints | Eachine Wizard | FS-i6 | WANTD:E5Mix Flysky fs-i6 for robot tank steering🎮 FlySky i6 - stick problem - solutionFlysky i6 Dual Rate & ExpoFSi6X Failsafe Setup Tutorial - How to Use FlySky Transmitter Failsafe (fs-i6x, fs-i6)FlySky FS-i6X Elevons Setup Guide - How to Configure Transmitter functions for Flying WingsFLYSKY FSi6 - Kalibrasi Gimbal Stik INDONESIARC Simulator training setup - FlySky FS-i6XFlySky FS-i6 Best beginners radioWhat are End Points and How to Use Them - FlySky FS-i6S TutorialFlySky Two Servo Aileron SetupFlySky i6 Flaperons - 3 methodsTurnigy / FlySky TGY-i6 / FS-i6 Secret Hidden Menu