Predator 3500 Inverter Generator DIY wheels
The shaft arbors I used are Amazon number ASIN: B08695BLZ3 the 1/2 inch by 5/8 thick long version make sure you get long.
The wheels I used were Harbor Freight sku 47638.
I used 3M 5200 sealant around the wheel shafts, spacers and threaded locking pin. This should keep the vibrations from loosening anything.
If you want to use the plastic or solid rubber wheels you will need to the smaller diameter arbor extensions.
I did not reuse the lock as it vibrates so much in the original form and in the new wheels that it is louder than the generator. If I have to worry about the generator rolling away I can place the tow rope around one of the wheels.
These wheels do seem to make the generator sound smoother and you don’t feel as much vibrations.
I used two one 1 inch neodymium magnets JB welded to the bottom (outside) of the crankcase to pull any magnetic fibers to them. I then covered the magnets with 3M 5200 to prevent any oil or fuel from damaging the JB weld. While this is not as handy as a magnetite dip stick, I don’t trust them enough. Also, the magnets were 2 dollars and I had the JB weld. This is the same set up used on many transmissions and engines which create a lot more metal than this little engine with what I am assuming are a bunch of plastic gears anyway.
Видео Predator 3500 Inverter Generator DIY wheels канала Sailsailsailsail
The wheels I used were Harbor Freight sku 47638.
I used 3M 5200 sealant around the wheel shafts, spacers and threaded locking pin. This should keep the vibrations from loosening anything.
If you want to use the plastic or solid rubber wheels you will need to the smaller diameter arbor extensions.
I did not reuse the lock as it vibrates so much in the original form and in the new wheels that it is louder than the generator. If I have to worry about the generator rolling away I can place the tow rope around one of the wheels.
These wheels do seem to make the generator sound smoother and you don’t feel as much vibrations.
I used two one 1 inch neodymium magnets JB welded to the bottom (outside) of the crankcase to pull any magnetic fibers to them. I then covered the magnets with 3M 5200 to prevent any oil or fuel from damaging the JB weld. While this is not as handy as a magnetite dip stick, I don’t trust them enough. Also, the magnets were 2 dollars and I had the JB weld. This is the same set up used on many transmissions and engines which create a lot more metal than this little engine with what I am assuming are a bunch of plastic gears anyway.
Видео Predator 3500 Inverter Generator DIY wheels канала Sailsailsailsail
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
BEST Generator UPGRADE for $50 / Go Anywhere!Predator 3500 Generator Wheel Removal + Wheel Mod IdeaPredator 3500 Upgraded Wheel Kit Installation and Field Test!PREDATOR 3500 GENERATOR MAINTENANCE SERVICE - BATTERY, ARRESTOR, SPARK PLUG, OIL CHANGE, AIR FILTERPredator 3500 Wheeled cartPredator 3500 Generator Exhaust Extension MODHarbor Freight 3500 Watt Inverter Generator - MUST SEE Tips & TricksDIY Predator 3500 generators paralleled with a Firman 1201Harbor Freight predator 3500 wheel upgradePredator 3500 ModsPredator 3500 Generator - surging problem fixed!Predator 3500 Charcoal Canister Delete!Predator 3500 Extended Run Time Fuel Kit Install by Pinellas Power ProductsPredator 3500 big wheels installation step by stepHF PREDATOR 3500 REVIEW 1500 HOURSPredator 3500 Plug & Play Remote Start & Stop Install Video (NEW & UPDATED with Kill Switch!)I Wish I Had Thought of This! BETTER Generator Wheel UPGRADE.Predator 3500 Inverter -Inside RV / CamperHarbor Freight Predator 3500 Watt Generator Pushed To The Limit!!Predator 3500 Inverter Generator 2 hour oil change LOTS OF METAL IN OIL a look with 250X microscope