It's Getting Exciting Now! -Part 5 ( Honda C90 FULL RESTORATION )
Welcome to part 5, Exciting times lay ahead with more building and engine work :)
The first job on today's list was to refit the swing arm to the frame but first it needed new bushes pressed into it so into the trusty old vice it went. After that it was just a case of bolt it to the frame and stick the rear wheel on. None of the rear end bolts will be torqued down at the moment as the chain still needs to be fitted and adjusted once the engine goes in.
After the wheel was on i decided to finish off most of the wiring by fitting the handlebars,switch gear and lights. This took longer than expected due to the polishing and inlaying that the switches needed but a job that was immensely satisfying to see the results of!
The it was onto the big job that a lot of you have been waiting for tearing the engine apart for restoration. At this point i would like to say all specs have been check for the engine and everything is within those specs so the gearbox wont be coming apart neither will the bore be getting honed or the piston replaced as compression tests show it has full compression. The casing were all lightly blasted then buffed back to a satin finish, a vapor blaster would make this process easier but i dont have one and no one local has one either so im stuck doing cases the hard way for now. The barrel was painted high temp gloss black and the side cases were repainted in there original silver gloss finish.
Next week i will be rebuilding the engine with all new gaskets and seals setting the tappets and ignition timing, then refitting the engine and finishing off the bike.... fingers crossed.
see you again soon RRC.
A little more info below if this is your first time watching the C90 restoration.
The item in question is a 1979 Honda C90 motorcycle , scooter, moped or whatever else you want to class it as lol. It was a barn find that has been sitting off the road for years and when i got the chance to buy it i snapped it up.
From the initial inspection it didn't look to bad but tearing it down uncovered a series of areas that will need rectification work if i want to get this back to factory fresh.
The plan is to go thorough the bike methodically restoring, replacing and fabricating as need be to make this one of the best restored c90's out there and as you can probably tell from my other videos the finish will be second to none ;)
so sit back relax and enjoy a series of videos documenting the full restoration of the bike from start to finish.
If you like what you see and have any ideas for the channel or would even like to donate something to restore to the channel please get in touch. :)
And as usual if you liked the video please like share and subscribe and help the channel grow.
Really Random Channel
#Restoration #Project #C90
It's Getting Exciting Now! -Part 5 ( Honda C90 FULL RESTORATION )
Видео It's Getting Exciting Now! -Part 5 ( Honda C90 FULL RESTORATION ) канала RRC Restoration
The first job on today's list was to refit the swing arm to the frame but first it needed new bushes pressed into it so into the trusty old vice it went. After that it was just a case of bolt it to the frame and stick the rear wheel on. None of the rear end bolts will be torqued down at the moment as the chain still needs to be fitted and adjusted once the engine goes in.
After the wheel was on i decided to finish off most of the wiring by fitting the handlebars,switch gear and lights. This took longer than expected due to the polishing and inlaying that the switches needed but a job that was immensely satisfying to see the results of!
The it was onto the big job that a lot of you have been waiting for tearing the engine apart for restoration. At this point i would like to say all specs have been check for the engine and everything is within those specs so the gearbox wont be coming apart neither will the bore be getting honed or the piston replaced as compression tests show it has full compression. The casing were all lightly blasted then buffed back to a satin finish, a vapor blaster would make this process easier but i dont have one and no one local has one either so im stuck doing cases the hard way for now. The barrel was painted high temp gloss black and the side cases were repainted in there original silver gloss finish.
Next week i will be rebuilding the engine with all new gaskets and seals setting the tappets and ignition timing, then refitting the engine and finishing off the bike.... fingers crossed.
see you again soon RRC.
A little more info below if this is your first time watching the C90 restoration.
The item in question is a 1979 Honda C90 motorcycle , scooter, moped or whatever else you want to class it as lol. It was a barn find that has been sitting off the road for years and when i got the chance to buy it i snapped it up.
From the initial inspection it didn't look to bad but tearing it down uncovered a series of areas that will need rectification work if i want to get this back to factory fresh.
The plan is to go thorough the bike methodically restoring, replacing and fabricating as need be to make this one of the best restored c90's out there and as you can probably tell from my other videos the finish will be second to none ;)
so sit back relax and enjoy a series of videos documenting the full restoration of the bike from start to finish.
If you like what you see and have any ideas for the channel or would even like to donate something to restore to the channel please get in touch. :)
And as usual if you liked the video please like share and subscribe and help the channel grow.
Really Random Channel
#Restoration #Project #C90
It's Getting Exciting Now! -Part 5 ( Honda C90 FULL RESTORATION )
Видео It's Getting Exciting Now! -Part 5 ( Honda C90 FULL RESTORATION ) канала RRC Restoration
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
The Grand Finale! -Part 6 ( Honda C90 FULL RESTORATION )1980 Honda Super Cub C50 Full Restoration | Will it run after 41 years!1978 Honda ATC 90 Full Restoration - Part 51978 Honda Super Cub C70 Frame RESTORATION | Restoration of 1978 Honda Super Cub C70 Part3Honda C50 Restoration 1971A Splash Of Colour -Part 2 ( Honda C90 FULL RESTORATION )1979 Honda Super Cub C50 Engine Restoration | Restoration Honda Cub C50Honda CB250N Engine Restoration | CB250 Hawk Engine RestorationHonda C50 Δείτε πως έγινε...!!! By MTP1980 Honda C70 SuperCub 2019 Build S4 Episode 130年放置のバイクレストア HONDA SUPER CUB(C70)【Part27】DIY ダイジェスト版【素人レストアDIY】Digest edition And nowJust Stand There! -Part 4 ( Honda C90 FULL RESTORATION )1978 Honda Super Cub C70 Full Restoration | Will It Run After 42 Years?1979 Honda Super Cub C50 Full Restoration | Will It Run After 40 Years?Honda Chaly Restoration1 year Super Cub custom project 一年がかりでスーパーカブをカスタムしてみた! #スーパーカブ #custommotorcycleYamaha Chappy Full Restoration | 80cc Chappy bike full RestorationHonda Wave Engine RESTORATION | Restoration Honda Wave Part2