H4 Alien 680mm quadcopter build and review - waterproofing and mounting ESC's [Part 6]
In this video we waterproof the ESCs and mount both the motors and the waterproofed ESC's. That was quite a lot of work to do that, but after some times you get the hang of it. In the next parts of this video series we will mount all the small bits and pieces like telemetry modules, buzzer, power module, receiver and so on, before setting up the pixhawk. The frame is carbon everywhere with red plastic clamps, so it is a foldable frame. All in all it seems a very good quality frame. This quadcopter should be used for mapping/photographing fields (with crop) from above. We'll see how that unfolds soon. Stay tuned and subscribe!
Parts used in this build:
Frame (H4 Alien 680 mm:
http://bit.ly/1xyS8Jq
Motors (Mulitstar 490kv):
EU: http://bit.ly/14gcScb
Global: http://bit.ly/1CX3KqW
ESC's (Blueseries 30A):
EU: http://bit.ly/1vMZH94
Global: http://bit.ly/1Hj8Eyi
Flightcontroller (3DR pixhawk w/ GPS):
http://www.robotshop.com/eu/en/3dr-px4-pixhawk-advanced-autopilot-gps.html
Propeller (15" carbon):
EU: http://bit.ly/13LO1vH
Global: http://bit.ly/1wHr7wt
Battery (4s 6000 mAh Nanotech):
EU: http://bit.ly/1D94uqd
Global: http://bit.ly/1tH7RVi
Camera holder (Battery holder H.A.L.):
EU: http://bit.ly/1y8VFey
Global: http://bit.ly/1w9caDb
Видео H4 Alien 680mm quadcopter build and review - waterproofing and mounting ESC's [Part 6] канала MultiCopterBuild
Parts used in this build:
Frame (H4 Alien 680 mm:
http://bit.ly/1xyS8Jq
Motors (Mulitstar 490kv):
EU: http://bit.ly/14gcScb
Global: http://bit.ly/1CX3KqW
ESC's (Blueseries 30A):
EU: http://bit.ly/1vMZH94
Global: http://bit.ly/1Hj8Eyi
Flightcontroller (3DR pixhawk w/ GPS):
http://www.robotshop.com/eu/en/3dr-px4-pixhawk-advanced-autopilot-gps.html
Propeller (15" carbon):
EU: http://bit.ly/13LO1vH
Global: http://bit.ly/1wHr7wt
Battery (4s 6000 mAh Nanotech):
EU: http://bit.ly/1D94uqd
Global: http://bit.ly/1tH7RVi
Camera holder (Battery holder H.A.L.):
EU: http://bit.ly/1y8VFey
Global: http://bit.ly/1w9caDb
Видео H4 Alien 680mm quadcopter build and review - waterproofing and mounting ESC's [Part 6] канала MultiCopterBuild
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
H4 Alien 680mm quadcopter build and review - mounting electronics [Part 7]H4 Alien 680mm quadcopter build and review - Landing Gear [Part 4]DIY drone (Part Two) | S500 | Pixhawk | FPV Quadcopter |H4 Alien 680mm quadcopter build and review - waterproofing electronics test [Part 2]First Flight! Tarot 650 Sport Extended Arm Drone with Pixhawk 4 (Awesome Flight Time!)H4 Alien 680mm quadcopter build and review - mounting pixhawk [Part 5]Finally! How To Wire Any 4 in 1 ESCInstalling PPM EncoderH4 Alien 680mm quadcopter build and review - waterproofing Pixhawk [Part 3]Cleanest Built Pixhawk 2.4.8 Drone | F450 frameH4 Alien 680mm quadcopter build and review - first look [Part 0]Tarot IRONMAN 650 build and review - Mounting ESC and Motor [Part 6]Tarot 680 Pro Hexacopter Build Part 3Jumper 218 pro initial thoughts (Review part 1)H4 Alien 680mm quadcopter build and review - Stripping the frame [Part 1]H4 Alien 680mm quadcopter build and review - Summary and flight [Part 9]Daya H4 680 // Arducopter // Maiden Flight & Crash7 CRAZY Homemade Manned DronesTarot 680 Pro Hexacopter : 40A ESC Mounting under Motor (ZTW)Upgrade cx20 apm to pixhawk