Tarot 680 Pro Hexacopter : Mounting Motors and More Soldering
Please SUBSCRIBE, COMMENT, and LIKE this video if you found it helpful! Thanks! http://everythingcpo.com
This video takes us through the installation of the motors onto the ESC/motor mounts, and attachment to the booms, and the soldering of the ESC wires to the PCB. I mention this in the video as an afterthought, but you could totally shorten the ESC wires to be more of a precise fit. I didn't, and it doesn't bother me. Those wires aren't visible once the final assembly is complete anyway.
The last thing of note is with regard to the right direction of the "front" of the PCB panel. I have decided that the side with the battery terminals should be the back on my build, since the camera gimbal will be up front. This works fine, but note that if you are planning on using a canopy, this will pose a problem, since Tarot designed it with the battery terminals in the FRONT. Strange, I know. It's not a problem if you do it either way, but if you want the canopy, you should do it opposite of what I did, or just know that the RED is in the back instead of the front (which is also something I thought hard about).
Anyway...thanks for watching.
Видео Tarot 680 Pro Hexacopter : Mounting Motors and More Soldering канала EVERYTHING cpo
This video takes us through the installation of the motors onto the ESC/motor mounts, and attachment to the booms, and the soldering of the ESC wires to the PCB. I mention this in the video as an afterthought, but you could totally shorten the ESC wires to be more of a precise fit. I didn't, and it doesn't bother me. Those wires aren't visible once the final assembly is complete anyway.
The last thing of note is with regard to the right direction of the "front" of the PCB panel. I have decided that the side with the battery terminals should be the back on my build, since the camera gimbal will be up front. This works fine, but note that if you are planning on using a canopy, this will pose a problem, since Tarot designed it with the battery terminals in the FRONT. Strange, I know. It's not a problem if you do it either way, but if you want the canopy, you should do it opposite of what I did, or just know that the RED is in the back instead of the front (which is also something I thought hard about).
Anyway...thanks for watching.
Видео Tarot 680 Pro Hexacopter : Mounting Motors and More Soldering канала EVERYTHING cpo
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Tarot 680 Pro Hexacopter : ESC Calibration and Motor DirectionsTarot 680 Pro Hexacopter : 40A ESC Mounting under Motor (ZTW)Tarot 680 Pro Hexacopter : Build Tips and UpdateTarot FY680 Build - Electronics - eRCMK7 5 Golf R Haldex Service (Fluid Change + Filter Clean) - SHOULD YOU PRIME THE PUMP?Tarot FY680 Build - Frame Assembly - eRCTarot FY680 Build - Setup - eRCTarot 650 Sport Rebuild!Tarot 680 Pro - Motors - Props - Battery - GimbalSOLUTION: Fix Leaking APR Catch Can PCV Plate!Tarot 680 Pro hex demoHMF S550 Hexacopter ESC Wire Trim and FlightTarot 650 Sport Build Installation Instructions DIY QuadcopterFrSky Taranis 3 Flight Modes and Forced Failsafe Override with DJI NAZA on QAV400 QuadcopterMK7.5 Golf R Rear Brakes : Pads, Rotors, and Stainless Steel LinesTarot 680 Pro Hexacopter Build Part 3Switching fuels and EQT tunes from E85 to 93Pixhawk 4 Setup and Calibration with QGroundControl | Pixhawk 4 + S500 Drone Build Tutorial | Part 4APM 2.6 Tarot FY680 Hexacopter Afro 30a ESC Turnigy Multistar 3508-640Kv Tarot GoPro GimbalTarot 680 PRO review and thoughts