ImpulseRC Apex HD DJI FPV - Full Build Tutorial
The ImpulseRC Apex HD is one of the best freestyle frames you can buy. Here's a complete step by step build and setup video showing how to build an ImpulseRC Apex HD with DJI FPV system.
This build video was made as part of FLOWSTATE: The FPV Drone Documentary, a feature-length documentary about FPV in the shadow of RemoteID. Watch the trailer at: https://youtu.be/8TMUfvTD2qs
--- VIDEO LINKS ---
How to install Betaflight and BLHeli:
https://www.youtube.com/watch?v=bAqgPEW48Tc
How to remap motors and correct FC board alignment:
https://www.youtube.com/watch?v=QeuSq71pYF0
How to set endpoints and channel center:
https://www.youtube.com/watch?v=1azl1f8qJ84&ab_channel=JoshuaBardwell
--- PRODUCT LINKS ---
All the tools and supplies you need to build a quad are listed at:
* Tools - https://www.fpvknowitall.com/ultimate-fpv-shopping-list-tools/
* Supplies - https://www.fpvknowitall.com/fpv-shopping-list-supplies/
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
DJI Goggles and Air Unit kit
* Rotor Riot - https://bit.ly/2Tipmey
* GetFPV - https://bit.ly/37CV12K
* RaceDayQuads - https://bit.ly/34mMdMg
* NewBeeDrone - https://bit.ly/2TkTje3
* Banggood - https://bit.ly/34rgDxb (be sure to select 2 air units 1 goggle!!!)
* Amazon - https://amzn.to/35wlg8a
Apex HD Frame kit (by Impulse RC)
* RaceDayQuads - https://bit.ly/34oShUJ
* GetFPV - https://bit.ly/3jjNQyE
* Newbeedrone - https://bit.ly/2FUQ0Hj
4x Blaster 2207 1800KV motors
* Rotor Riot - https://bit.ly/3jjnA7C
T-Motor F7 F55A Pro II HD (DJI compatible) Stack
* RaceDayQuads - https://bit.ly/3kCqFRq
* Banggood - https://bit.ly/2HsYwhl
* Amazon - https://amzn.to/31yofvO
Batteries (buy several!)
* RaceDayQuads - https://bit.ly/3jq4WLk
* GetFPV - https://bit.ly/37y18W9
* Banggood - https://bit.ly/34qfvtw
TBS Crossfire Starter Set (module, receiver, antenna)
* GetFPV - https://bit.ly/3abBhm2
* Team Blacksheep - https://bit.ly/34mFhyK
Ethix Lemon lime propellers
* GetFPV - https://bit.ly/3kuKwlG
* RaceDayQuads - https://bit.ly/34lvusS
* NewBeeDrone - https://bit.ly/34oTtaF
Purchase the ViFly ShortSaver at
* Amazon (ViFly store) - https://amzn.to/2ZCgGns
* GetFPV - https://bit.ly/33mCx4r
* RaceDayQuads - https://bit.ly/2ENSMgL
* Newbeedrone - https://bit.ly/3fLCwJG
* Banggood - https://bit.ly/3kaLlAa
Okay now the awkward part. The radio that we used in the tutorial is James's QX7. But that radio has since gone out of production. The radio that I recommend to replace it is the RadioMaster TX16S. The screen is bigger and the buttons are nicer. But the hard part is that the screens won't look exactly like they do in the tutorial, even though both radios ARE running the same operating system and the setup steps are more or less the same.
RadioMaster TX16S
* RaceDayQuads - https://bit.ly/3dsu3KX
* NewBeeDrone - https://bit.ly/3ollx6y
* Banggood - https://bit.ly/3fJ8LL4
* Amazon - https://amzn.to/31BSlyp
3d printed mounts are on Thingiverse. You can print yourself or you can order them printed from a 3D printing service like RaceDayQuads, GetFPV, Brain3D, or BMC3D.
Apex HD Frame - GoPro Mount - 30 Deg: https://www.thingiverse.com/thing:4605640
APEX HD - Air Unit & Immortal T Adapter: https://www.thingiverse.com/thing:4605652
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
Most or all links above are affiliate links, and I will receive compensation if you use them.
--- TABLE OF CONTENTS ---
0:00 - Intro
2:44 - Parts used in the build
5:47 - Assemble the arms and bottom plate of the frame
13:27 - Install the motors
20:21 - Mount the Air Unit and antennas
24:57 - Mount the ESC and tin the pads
31:57 - Prep and solder the XT60 lead
34:01 - Smoke check
36:12 - Solder the motor wires
39:28 - Solder and mount the receiver
43:25 - Mount the camera
46:58 - Bind receiver and set up model in radio
49:24 - Betaflight Setup
1:11:18 - DJI system activation and firmware update
1:14:27 - Final assembly
1:18:23 - Flight test!
Видео ImpulseRC Apex HD DJI FPV - Full Build Tutorial канала Joshua Bardwell
This build video was made as part of FLOWSTATE: The FPV Drone Documentary, a feature-length documentary about FPV in the shadow of RemoteID. Watch the trailer at: https://youtu.be/8TMUfvTD2qs
--- VIDEO LINKS ---
How to install Betaflight and BLHeli:
https://www.youtube.com/watch?v=bAqgPEW48Tc
How to remap motors and correct FC board alignment:
https://www.youtube.com/watch?v=QeuSq71pYF0
How to set endpoints and channel center:
https://www.youtube.com/watch?v=1azl1f8qJ84&ab_channel=JoshuaBardwell
--- PRODUCT LINKS ---
All the tools and supplies you need to build a quad are listed at:
* Tools - https://www.fpvknowitall.com/ultimate-fpv-shopping-list-tools/
* Supplies - https://www.fpvknowitall.com/fpv-shopping-list-supplies/
I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.
DJI Goggles and Air Unit kit
* Rotor Riot - https://bit.ly/2Tipmey
* GetFPV - https://bit.ly/37CV12K
* RaceDayQuads - https://bit.ly/34mMdMg
* NewBeeDrone - https://bit.ly/2TkTje3
* Banggood - https://bit.ly/34rgDxb (be sure to select 2 air units 1 goggle!!!)
* Amazon - https://amzn.to/35wlg8a
Apex HD Frame kit (by Impulse RC)
* RaceDayQuads - https://bit.ly/34oShUJ
* GetFPV - https://bit.ly/3jjNQyE
* Newbeedrone - https://bit.ly/2FUQ0Hj
4x Blaster 2207 1800KV motors
* Rotor Riot - https://bit.ly/3jjnA7C
T-Motor F7 F55A Pro II HD (DJI compatible) Stack
* RaceDayQuads - https://bit.ly/3kCqFRq
* Banggood - https://bit.ly/2HsYwhl
* Amazon - https://amzn.to/31yofvO
Batteries (buy several!)
* RaceDayQuads - https://bit.ly/3jq4WLk
* GetFPV - https://bit.ly/37y18W9
* Banggood - https://bit.ly/34qfvtw
TBS Crossfire Starter Set (module, receiver, antenna)
* GetFPV - https://bit.ly/3abBhm2
* Team Blacksheep - https://bit.ly/34mFhyK
Ethix Lemon lime propellers
* GetFPV - https://bit.ly/3kuKwlG
* RaceDayQuads - https://bit.ly/34lvusS
* NewBeeDrone - https://bit.ly/34oTtaF
Purchase the ViFly ShortSaver at
* Amazon (ViFly store) - https://amzn.to/2ZCgGns
* GetFPV - https://bit.ly/33mCx4r
* RaceDayQuads - https://bit.ly/2ENSMgL
* Newbeedrone - https://bit.ly/3fLCwJG
* Banggood - https://bit.ly/3kaLlAa
Okay now the awkward part. The radio that we used in the tutorial is James's QX7. But that radio has since gone out of production. The radio that I recommend to replace it is the RadioMaster TX16S. The screen is bigger and the buttons are nicer. But the hard part is that the screens won't look exactly like they do in the tutorial, even though both radios ARE running the same operating system and the setup steps are more or less the same.
RadioMaster TX16S
* RaceDayQuads - https://bit.ly/3dsu3KX
* NewBeeDrone - https://bit.ly/3ollx6y
* Banggood - https://bit.ly/3fJ8LL4
* Amazon - https://amzn.to/31BSlyp
3d printed mounts are on Thingiverse. You can print yourself or you can order them printed from a 3D printing service like RaceDayQuads, GetFPV, Brain3D, or BMC3D.
Apex HD Frame - GoPro Mount - 30 Deg: https://www.thingiverse.com/thing:4605640
APEX HD - Air Unit & Immortal T Adapter: https://www.thingiverse.com/thing:4605652
MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
Most or all links above are affiliate links, and I will receive compensation if you use them.
--- TABLE OF CONTENTS ---
0:00 - Intro
2:44 - Parts used in the build
5:47 - Assemble the arms and bottom plate of the frame
13:27 - Install the motors
20:21 - Mount the Air Unit and antennas
24:57 - Mount the ESC and tin the pads
31:57 - Prep and solder the XT60 lead
34:01 - Smoke check
36:12 - Solder the motor wires
39:28 - Solder and mount the receiver
43:25 - Mount the camera
46:58 - Bind receiver and set up model in radio
49:24 - Betaflight Setup
1:11:18 - DJI system activation and firmware update
1:14:27 - Final assembly
1:18:23 - Flight test!
Видео ImpulseRC Apex HD DJI FPV - Full Build Tutorial канала Joshua Bardwell
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Mr. Steele Apex converted to FETTEC and DJI | complete how toJB's Perfect Racing Drone Build 2021 | FULL BUILD TUTORIAL (533 Switchback Pro)Freestyle Quad Full Build Tutorial NEWBEEDRONE VIVID HD KITI BUILT Mr Steele's APEX to SPEC. Is it really THAT good? + Mr Steele PIDS and RATES / STICK CAMBeginner Guide // How To Build Budget DJI Cinematic FPV Drone 2020ImpulseRC Apex HD | Build And ReviewMind blowing LED props for your FPV drone | GEMFAN MOONLIGHT V2Rotor Riot Spec Kwad - HD1 Build with DJI FPV SystemMY IMPULSERC APEX FPV DRONE SETUP? (PIDS!) 😯🔥💀 | FPV FREESTYLEFPV Drone Budget Build Full Tutorial - Part 1 - AssemblyHow To Assemble The Apex Frame by ImpulseRCBuild: The CL1 Vannystyle (with CaptainVanover)Apex Clones Comparison | ReadyToSky AliExpress vs Banggood | FPV Freestyle FrameHow to Build Ultimate Budget FPV Drone Build 2021 // Beginner GuideDiatone Roma F5 is the new best FPV quad under $200Build Your Own DJI FPV Quadcopter - Part 2 - How to connect DJI Air Unit to Betaflight FCWhy it's so hard to hover an FPV racing drone6 Ways to RUIN Your FPV Drone!New Caddx Air Unit Replaces DJI Air Unit! Is It Any Good?No More Alien? NEW APEX Freestyle/Cine Rundown (PIDs Included)🥳