Build Your Own DJI FPV Quadcopter - Part 1 - Initial Assembly

Uncertain about what to buy? Check out THE ULTIMATE FPV SHOPPING LIST: https://www.fpvknowitall.com/ultimate-fpv-shopping-list

SUPPORT ME ON PATREON at: http://bit.ly/2Ep5Sia

THIS IS MY FULL TIME JOB. Here are other ways that you can support me: https://www.fpvknowitall.com/support-me/
---

I'm going to teach you how to build your own DJI HD FPV quadcopter. If this is your first FPV quadcopter build, I'll show you every step that you need to know to build your first FPV quadcopter. If you're an experienced builder, I'll show you just the parts that are new to the DJI system.

--- VIDEO LINKS ---

The full playlist for this build series is:
https://www.youtube.com/playlist?list=PLwoDb7WF6c8n5d8D1JhPhyBYwe-r_PemW

If you decide to flip the ESC around 180 degrees, here is how to fix the board alignment and motor mapping:

https://www.youtube.com/watch?v=QeuSq71pYF0

This is one of the best soldering tutorials I've seen. Don't let the fact that it was filmed a long time ago turn you off. Basic, no-BS information. Watch ALL OF THIS.

https://www.youtube.com/watch?v=vIT4ra6Mo0s

My video about what a smoke stopper is and how to make one:

https://www.youtube.com/watch?v=I5a0TAmEwLE

--- PRODUCT LINKS ---

I receive a commission (at no extra cost to you) if you make a purchase after clicking one of the affiliate links below.

WANT TO JUST BUY A READY TO FLY PRE-TUNED QUAD INSTEAD OF BUILDING ONE? I won't judge you...
* Rotor Riot - http://bit.ly/2Mkq4nP
* GetFPV - http://bit.ly/35iOUgj

Purchase the DJI HD Digital FPV System at:
* GetFPV - http://bit.ly/2T1328b
* RaceDayQuads - http://bit.ly/2MzzNZ3
* Rotor Riot - http://bit.ly/2MEVSFP
* Newbeedrone - http://bit.ly/2yY2wi6
* Banggood - http://bit.ly/30Q9JNI

Purchase the Rotor Riot HD1 Frame at:
* Rotor Riot - http://bit.ly/2OtY0Ba

Purchase the Newbeedrone Infinity FC and ESC combo at:
* RaceDayQuads - http://bit.ly/2VnMgkM
* NewBeeDrone - http://bit.ly/30R2hRH

Purchase the Rotor Riot Blaster motors at:
* Rotor Riot - http://bit.ly/2LUkiKl
* RaceDayQuads - http://bit.ly/2SExuUB
* GetFPV - http://bit.ly/2shsoCw

The M3 screw assortment that I use in this video is:
* Amazon - https://amzn.to/2Iuo2As

Purchase Ummagrip battery pad at:
* GetFPV - http://bit.ly/35eJkLT
* RaceDayQuads - http://bit.ly/2oY88Y2
* Rotor Riot - http://bit.ly/2Vo3azZ

Purchase the pre-built XT60 pigtail at:
* Amazon - https://amzn.to/2LTVpia

Recommended Battery for this build is 4S 1300 to 1600 mAh. My suggested batteries are at https://www.fpvknowitall.com/fpv-shopping-list-charging#batteries

Recommended props for this build are Gemfan Hurricane 51466
* RaceDayQuads - http://bit.ly/2IyqWUF
* GetFPV - http://bit.ly/2Iw48F4
* Banggood - http://bit.ly/2IuSWbV
* Rotor Riot - http://bit.ly/35eDVoj

MANDATORY DISCLAIMER: I am a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.

Most or all links above are affiliate links, and I will receive compensation if you use them.

Видео Build Your Own DJI FPV Quadcopter - Part 1 - Initial Assembly канала Joshua Bardwell