Drill HACK 1 metal cutting BANDSAW part 2
Hi. My name is Darek and in this video I'll show you how I finished building homemade metal cutting band saw powered by drill.
I could not set the tape so I remake wheel, it was a great decision.
Needed a set of bearings with the housing, for this purpose, I used parts from an old bike frame because I like to use unnecessary things.
I cut a hole in the frame, so that after screwing and welding have an angle of about 50 degrees.
As a base I used a metal sheet thickness of 3mm and squer tubbing 20x20x2 mm.
Blade guides I made with angle 25x25x3, does not look professionally, but it does the job. All bearings are of the same size 8x22x7 mm.
The vice is a Czech company PROMA SV-75 should be biger, but I used which is in the shop. I can adjust the angle from 0 to 50 degrees. With the way mounting vice to the flat I adjust the angle of zero.
Saw frame is quite heavy so I used the spring, so I can lift it with one finger.
With this device you have to be very careful, so I hid the blade and the wheel - I used the speaker grilles that were not needed to me :)
Saw on the film does not cut quickly because almost no pushing it, I have to get used to it :)
It cuts almost perfect, but it still must be adjusted a little bit :)
If you liked this video, click the thumbs up :)
----------------------------------------------------------------------------
Follow me on:
INSTAGRAM www.instagram.com/made_inpoland/
FACEBOOK www.facebook.com/1187887134621389/
----------------------------------------------------------------------------
Business contact: darus627@gmail.com
Видео Drill HACK 1 metal cutting BANDSAW part 2 канала Made in Poland
I could not set the tape so I remake wheel, it was a great decision.
Needed a set of bearings with the housing, for this purpose, I used parts from an old bike frame because I like to use unnecessary things.
I cut a hole in the frame, so that after screwing and welding have an angle of about 50 degrees.
As a base I used a metal sheet thickness of 3mm and squer tubbing 20x20x2 mm.
Blade guides I made with angle 25x25x3, does not look professionally, but it does the job. All bearings are of the same size 8x22x7 mm.
The vice is a Czech company PROMA SV-75 should be biger, but I used which is in the shop. I can adjust the angle from 0 to 50 degrees. With the way mounting vice to the flat I adjust the angle of zero.
Saw frame is quite heavy so I used the spring, so I can lift it with one finger.
With this device you have to be very careful, so I hid the blade and the wheel - I used the speaker grilles that were not needed to me :)
Saw on the film does not cut quickly because almost no pushing it, I have to get used to it :)
It cuts almost perfect, but it still must be adjusted a little bit :)
If you liked this video, click the thumbs up :)
----------------------------------------------------------------------------
Follow me on:
INSTAGRAM www.instagram.com/made_inpoland/
FACEBOOK www.facebook.com/1187887134621389/
----------------------------------------------------------------------------
Business contact: darus627@gmail.com
Видео Drill HACK 1 metal cutting BANDSAW part 2 канала Made in Poland
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Homemade Metal Band SawSerra Fita Horizontal - Montagem -- Горизонтальная ленточная пилаЛенточная пила по металлу изготовление серия 2CHEAP Spot Welder DIY (using simple tools) [PLANS]Homemade Belt Grinder made from Trash DIYSega a nastro portatile fai da te (homemade portable bandsaw)ELECTROMAGNETIC Drill Press Stand [PLANS]Drill HACK 1 metal cutting BANDSAW part 1DIY Metal Cutting Horizontal/Vertical Band SawConcrete fence post Removal ToolMaking plasma cutting trackDril HACK 2 belt sander 6x48"Homemade Portable Bandsaw Stand - Cut off & Vertical - Part 1Bandsaw for Metall How To MakeЛенточная пила по металлу изготовление серия 3Setting up small metalworking workshopChange CIRCULAR SAW to CHOP SAWMini SCREW LOG SPLITTER (made from scrap)Electromagnetic Drill press VISE [PLANS]Hydraulic CAR JACK modification