How to setup your TBS Tango II Crossfire Radio to work with Betaflight
All the essential setup instructions you need to know so you can configure your TBS Tango II radio to talk to your Betaflight Flight controller and quickly get your drone in the air.
I just recently switched from my DJI FPV radio to this Tango 2 radio. Since this was my first OpenTX ( or FreedomTX) based radio I had a lot to learn and thought I would share my experience.
I expect there is a whole bunch of new people who just got the Tango II and DJI FPV as their first FPV drone and need a handy setup guide to get them going. If that is you, I hope this video saves you some time and frustration.
TABLE OF CONTENTS:
0:00 Intro
0:26 Wiring Guide
4:07 Tango II and Crossfire Firmware Update
4:58 Binding the Receiver
7:56 Crossfire Receiver Settings
10:05 Betaflight Settings
12:05 Create a New Model in the Radio
18:57 Stick Calibration
20:48 Discover Sensors
21:32 Double Check Failsafe!
22:14 LQ in DJI OSD
25:17 Audio Alerts for Radio Signal Strength
Tango II Firmware Update Video:
https://youtu.be/SVO8OL9cDzE
Oscar Liang Crossfire and RSSI Tutorial:
https://oscarliang.com/lq-rssi-tbs-crossfire/
Tango II Manual:
https://www.team-blacksheep.com/tbs-tango2-manual.pdf
GetFPV Referral Link: https://www.getfpv.com/r/146411/
#fpv #teamblacksheep #djifpv
Видео How to setup your TBS Tango II Crossfire Radio to work with Betaflight канала 5zero7 RC
I just recently switched from my DJI FPV radio to this Tango 2 radio. Since this was my first OpenTX ( or FreedomTX) based radio I had a lot to learn and thought I would share my experience.
I expect there is a whole bunch of new people who just got the Tango II and DJI FPV as their first FPV drone and need a handy setup guide to get them going. If that is you, I hope this video saves you some time and frustration.
TABLE OF CONTENTS:
0:00 Intro
0:26 Wiring Guide
4:07 Tango II and Crossfire Firmware Update
4:58 Binding the Receiver
7:56 Crossfire Receiver Settings
10:05 Betaflight Settings
12:05 Create a New Model in the Radio
18:57 Stick Calibration
20:48 Discover Sensors
21:32 Double Check Failsafe!
22:14 LQ in DJI OSD
25:17 Audio Alerts for Radio Signal Strength
Tango II Firmware Update Video:
https://youtu.be/SVO8OL9cDzE
Oscar Liang Crossfire and RSSI Tutorial:
https://oscarliang.com/lq-rssi-tbs-crossfire/
Tango II Manual:
https://www.team-blacksheep.com/tbs-tango2-manual.pdf
GetFPV Referral Link: https://www.getfpv.com/r/146411/
#fpv #teamblacksheep #djifpv
Видео How to setup your TBS Tango II Crossfire Radio to work with Betaflight канала 5zero7 RC
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
TBS Tango 2 bootloader mode and how to update. Cold radio issue, Brick FIX, and many other issues!Koleksi Lagu Raya Evergreen TerbaikTBS Tango 2 set-up guide instructionsTBS Tango 2 - Unboxing and First FlightsHow to Bind Your Crossfire RX to a New Radio the Easy WayTBS Tango 2 500 mW Firmware Update How ToHow to Adjust Tango 2 Gimbal Tension StrengthFinally! Quick Guide To Setting Up Crossfire Nano! How To Wire & Install & ProgramTBS Tango 2 very nearly the best radio (UPDATED REVIEW IN COMMENTS)Where Is The Bind Button On The Nazgul5 V2 TBS Crossfire and How To Bind ItTBS Crossfire frequency & region causes failsafe at short range when set incorrectlyTBS TANGO 2---easy setup guardTBS Tango II: Creating a basic model memoryTBS Sixty9 should probably replace your Unify (full review and setup guide!)DJI Crossfire LQ in OSD How ToTBS Tango 2 Compact Long Range TransmitterTBS Tango 2 how to set-up RSSI / LQ / TelemetryBetaflight 3.4 & 3.5 Setup For Total BeginnersTBS acknowledges Crossfire binding bug (double flash green LED)TBS Multiprotocol Module IS TANGO 2 NOW THE BEST RADIO YOU CAN BUY