Adding a BMS to the 38120 battery
In the last video, I showed you how to make a busbar, and assemble the batteries to make a 24 Volt system.
In this video, I will show you how to add a BMS to the battery.
I picked up this Daly LIFEP04 8S 24 Volt common port BMS from AliExpress for $55 shipped.
First, we have to install the 9 wire balance cable to the battery.
After all of the wires have been stripped, we start with the first red cable furthest from the black negative cable, and that connects to the main battery positive terminal.
The 2nd cable connects to the 2nd positive terminal in series on the battery.
The 3rd cable connects to the 3rd positive terminal in series on the battery.
I think you got it from here.
The black ground cable connects to the batteries main negative terminal.
After all cables have been installed, lets do a quick check on the batteries voltage.
The battery reads 26.3 Volts.
Lets unscrew this so we can add the blue B- cable on the batteries main negative terminal.
And now connect the balance cable to the BMS.
Now that everything has been installed, lets check the voltage.
The negative on the multimeter connects to the P-, and the positive connects to the batteries main positive.
And we have a reading of 26.3. This means the BMS is operating correctly.
If this does not read the voltage we checked earlier, your wiring is not correct. Check your wiring and retest.
Lets clean up our install a bit.
That looks a lot better.
The main negative is now the P-. Do not connect a load to the main batteries negative terminal or the BMS will not balance, discharge or charge correctly.
I think it came out well. I will be using this battery on my 10 gallon frag tank in case of an outage.
This video will finish it up for the 38120 build.
I hope you enjoyed it, and learned how to add a BMS.
If you have any questions, comments, or suggestions please post them below.
Видео Adding a BMS to the 38120 battery канала Ian K
In this video, I will show you how to add a BMS to the battery.
I picked up this Daly LIFEP04 8S 24 Volt common port BMS from AliExpress for $55 shipped.
First, we have to install the 9 wire balance cable to the battery.
After all of the wires have been stripped, we start with the first red cable furthest from the black negative cable, and that connects to the main battery positive terminal.
The 2nd cable connects to the 2nd positive terminal in series on the battery.
The 3rd cable connects to the 3rd positive terminal in series on the battery.
I think you got it from here.
The black ground cable connects to the batteries main negative terminal.
After all cables have been installed, lets do a quick check on the batteries voltage.
The battery reads 26.3 Volts.
Lets unscrew this so we can add the blue B- cable on the batteries main negative terminal.
And now connect the balance cable to the BMS.
Now that everything has been installed, lets check the voltage.
The negative on the multimeter connects to the P-, and the positive connects to the batteries main positive.
And we have a reading of 26.3. This means the BMS is operating correctly.
If this does not read the voltage we checked earlier, your wiring is not correct. Check your wiring and retest.
Lets clean up our install a bit.
That looks a lot better.
The main negative is now the P-. Do not connect a load to the main batteries negative terminal or the BMS will not balance, discharge or charge correctly.
I think it came out well. I will be using this battery on my 10 gallon frag tank in case of an outage.
This video will finish it up for the 38120 build.
I hope you enjoyed it, and learned how to add a BMS.
If you have any questions, comments, or suggestions please post them below.
Видео Adding a BMS to the 38120 battery канала Ian K
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
Headway 38120s LifePo4 50ah Battery Build with BMSBuild a DIY Lithium LiFePo4 Headway 12v Battery replacementLG Cells Part 2, 6kwh 48v DIY BatteryREC BMS: An Overview & the SetupHow to Properly Jump Start a CarTesting a New LiFePO4 BMS, 12v Battery Build and Aliexpress Cell TestSealed Lead Acid Battery Recovery39. Lithium Battery Management & Monitoring InstallBMS Battery Module - Can you Series connect them?Headway 45 amp hour 576wh 12.8 volt pack assemblyChargery BMS Overview for BYD 24 Volt BatteriesBuilding My First 24v LifePO4 Battery with raw cells - DIY Lithium iron phosphate12V Lithium Upgrade Headway 38120 Cells - 100A continuous (2018)Complete LiFePO4 Solar Battery System Design (Updated Blueprint in Description)Battery Reconditioning -- All Steps in 1 by Walt Barrett Made in USABMS or No BMS ? - 30 Month UpdateHeadway 38120 HP 200 Amp LifePO4 Cells Can They Start A Cold Car? Follow Up Questions and AnswersUsed 5.6kWh LiFePO4 Solar Battery w/BMS for $850 (bigbattery.com)How to properly solder 18650 batteries, fuses, & busbarsDIY: How to revive a dead 18650 (or any) Li-ion battery cell