BMW R1250GS / R1200GS : Important but Often Overlooked Maintenance Item (Spline Lube Tutorial)
Welcome to Big Rock Moto & Outdoors. I am a 100% independent, non-sponsored, non-commercial channel devoted to motorcycles, bicycles, honest product reviews, car and truck reviews, RV and camping content, and outdoor and mountain living. Please subscribe if you haven't already.
Follow me on:
Facebook: https://www.facebook.com/BigRockMoto/
Twitter: https://twitter.com/BigRockMoto1
Instagram: https://www.instagram.com/bigrockmoto/
IMPORTANT: Plan to change your final drive fluid at the same time you do this job. It will leak out the speedo/ABS sensor hole when you lower the final drive. Also, there are varying suggestions about what kind of grease or anti-seize compound to use, so do your own research. I used a moly synthetic grease. Some say to use a moly paste. Also, beware of the driveshaft pulling out from the other end, which then would require complicated re-assembly. Finally, grease the boot to help prevent water intrusion.
NOTE: My bike had never been apart before, it came dry like this from the factory!
If you are lucky maybe you have heard about lubing the splines on your GS. It doesn't seem to be in the service schedule. This is NOT changing the final drive fluid.
My splines were RUSTY and NOT GREASED at just 3k miles. Here is step by step how to do this.
Видео BMW R1250GS / R1200GS : Important but Often Overlooked Maintenance Item (Spline Lube Tutorial) канала Big Rock Media
Follow me on:
Facebook: https://www.facebook.com/BigRockMoto/
Twitter: https://twitter.com/BigRockMoto1
Instagram: https://www.instagram.com/bigrockmoto/
IMPORTANT: Plan to change your final drive fluid at the same time you do this job. It will leak out the speedo/ABS sensor hole when you lower the final drive. Also, there are varying suggestions about what kind of grease or anti-seize compound to use, so do your own research. I used a moly synthetic grease. Some say to use a moly paste. Also, beware of the driveshaft pulling out from the other end, which then would require complicated re-assembly. Finally, grease the boot to help prevent water intrusion.
NOTE: My bike had never been apart before, it came dry like this from the factory!
If you are lucky maybe you have heard about lubing the splines on your GS. It doesn't seem to be in the service schedule. This is NOT changing the final drive fluid.
My splines were RUSTY and NOT GREASED at just 3k miles. Here is step by step how to do this.
Видео BMW R1250GS / R1200GS : Important but Often Overlooked Maintenance Item (Spline Lube Tutorial) канала Big Rock Media
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
BMW R1250GSA DENALI D7 & S4 INSTALLATIONbmw r1200gs final drive boot grease service Maintenance ASMRFinal Drive Oil Change/Spline Lube BMW R1200GS/1250GS : DETAILED Step-by-Step InstructionsHow to Perform a Final Drive Service on a 2007 BMW R1200RTBMW Motorcycles - Worlds Biggest Motorbike Factory | Full DocumentaryBMW R 1200 GS Boxer Engine Production | HOW IT'S MADERekluse TorqDrive Installation for BMW 1200 and 1250ESSENTIAL MAINTENANCE: How to lube the FD splines on the shaft drive of your BMW R1250GS / R1200GSBMW R1200GS / R1250GS || Best Mods & UpgradesR1200GS / R1250GS | Complete Buyer's Guide [2005-2020]BMW R1200gs Adventure 2007 transmission spline lub & final drive rubber boot gaiter replacementBMW R1250GSA vs. Honda Africa Twin. Which one is better? In-depth ReviewHow to Perform a Valve Check and Adjustment on a 2008 R1200GSBMW R1200 GS Shaft Splines Lubrication / Service 🔧🔦😬2021 BMW R1250GS Review and Must-Have AccessoriesIf I could only pick one bike to ride forever...here's why | R1200GSA ReviewR1200/R1250GS Final Drive Fluid + Spline Lube + Magnetic Drain PlugBMW R1200GS Rear Drive Service + Brakes + Spline Lube + Final Drive FluidBMW R1200GS / R1250GS | Spline Lube & Final Drive Oil - Part IIFinal Drive Maintenance (2019 BMW R1250GSA)