SNS 159 Part 2: Machining a Large Hydraulic Tube Nut
This week I have a pretty nice machining project to tackle. This is a steel nut that goes onto a telescoping cylinder tube.It screws onto the tube end and hold the seals and bronze packing nut.
I'll use some heavy wall mechanical tubing and machine this in the American Pacemaker lathe.
Turning, facing, boring, and threading. I also have a face groove to cut on one side for an o-ring.
Enjoy!
Видео SNS 159 Part 2: Machining a Large Hydraulic Tube Nut канала Abom79
I'll use some heavy wall mechanical tubing and machine this in the American Pacemaker lathe.
Turning, facing, boring, and threading. I also have a face groove to cut on one side for an o-ring.
Enjoy!
Видео SNS 159 Part 2: Machining a Large Hydraulic Tube Nut канала Abom79
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
![Machining Hydraulic Cylinder Head Plates Part 1](https://i.ytimg.com/vi/gTfqBpUT7IE/default.jpg)
![SNS 161 Part 2: Machining Bronze Packing Nuts](https://i.ytimg.com/vi/LWSRig4lEIQ/default.jpg)
![Line boring and Bore welding Caterpillar D10 Dozer push arm | Sir Meccanica WS2](https://i.ytimg.com/vi/fMeHiT4yECk/default.jpg)
![LeBlond Lathe Cross-Feed Nut Part 1](https://i.ytimg.com/vi/Ft8TuQnWXgw/default.jpg)
![SNS 294 Kubota Crankshaft Hot Shot 360](https://i.ytimg.com/vi/bJwuB9Xy4rc/default.jpg)
![SNS 204: Thread Repair Inserts, Boring Mill, Large Gearbox Build, G&E Catalog](https://i.ytimg.com/vi/XHzLKu2Nlds/default.jpg)
![SNS 300: Spray Welding a Blower Shaft](https://i.ytimg.com/vi/FLYdhfgF6Pg/default.jpg)
![Repair DAMAGED Hydraulic Cylinder for CAT 16H Motor Grader | Machining & Welding](https://i.ytimg.com/vi/EiIrHB9CM6c/default.jpg)
![Repair DAMAGED Hydraulic Cylinder for CAT 651 Scraper | Part 1](https://i.ytimg.com/vi/-9ljmgzPmfA/default.jpg)
![SNS 157 Part 2: Failed Repair on Roll Journal](https://i.ytimg.com/vi/yy-rae-aUSc/default.jpg)
![Stainless Exhaust Collector Part 2](https://i.ytimg.com/vi/hSRHYL7hmBg/default.jpg)
![Machining a Dake Arbor Press Handwheel](https://i.ytimg.com/vi/prgN2eFWwFc/default.jpg)
![SNS 304 Part 1: Removing Broken Bolts, New Baldor Buffer](https://i.ytimg.com/vi/TkU_79e4Eho/default.jpg)
![SNS 147 Part 2: Shop Made Tap Driver](https://i.ytimg.com/vi/y1UFxZ59UnI/default.jpg)
![Forklift Axle Housing Repair](https://i.ytimg.com/vi/svsK6xuSdh0/default.jpg)
![Machining a Custom Prop Shaft Part 1](https://i.ytimg.com/vi/kKrdJdpx33M/default.jpg)
![Walker Turner Drilling Head Adaptor Part 2: Rotary Table Machining & Finishing](https://i.ytimg.com/vi/6Bq8Qm10Gvw/default.jpg)
![SNS 288 Machining an 18 Inch Straight Edge](https://i.ytimg.com/vi/NGNVPfLZb5I/default.jpg)
![Machining a Lock Part for a Custom Door](https://i.ytimg.com/vi/IKNuH85CLQY/default.jpg)
![SNS 210: Acme Nut Threading](https://i.ytimg.com/vi/CFWwNpSDHKM/default.jpg)