Загрузка страницы

APM 2.5 ArduCopter Quadcopter Return to Launch (RTL) Field Test in Windy Conditions - Austin, TX

A special thanks to my buddy Cory Kirk who, on a minute's notice, came to the field to film for me:

https://twitter.com/TEXASFREELANCER

This was my first ArduCopter APM 2.5 RTL test and the results were astounding. I was hesitant to flip the switch because of the amount of wind and how hard it was to control the quadcopter even in stabilize mode. I had my Turnigy 9X switch position 1 configured for RTL flight mode and if you need help setting it up then go here:

http://www.youtube.com/watch?v=6n_5wNA2jTI

Once I flipped into RTL mode the APM board was ecstatic to take control of the rotors. It quickly ascended to 50 ft and then started heading toward the launch location. The launch location is determined by having a GPS fix and where the quad was last armed.

The quad descended and loitered until I took control again. You'll see it's within a couple feet of the launch location. Very impressive.

Just FYI my parameter settings were the defaults of:

ALT_HOLD_RTL: 1500 (cm)
AUTO_LAND: 5000 (milliseconds)
APPROACH_ALT: 200 (cm)

These worked beautifully out of the box. I hope this video was useful and let me know if you have any problems setting this up.

Good luck!

Видео APM 2.5 ArduCopter Quadcopter Return to Launch (RTL) Field Test in Windy Conditions - Austin, TX канала Dennis Baldwin
Показать
Комментарии отсутствуют
Введите заголовок:

Введите адрес ссылки:

Введите адрес видео с YouTube:

Зарегистрируйтесь или войдите с
Информация о видео
12 января 2013 г. 4:49:18
00:04:25
Другие видео канала
Phantom 3 and Phantom 4 RC Flight Mode Switch Explained for 3rd Party AppsPhantom 3 and Phantom 4 RC Flight Mode Switch Explained for 3rd Party AppsReversing Motor Rotation with Castle Creations Multirotor ESCs and Castle LinkReversing Motor Rotation with Castle Creations Multirotor ESCs and Castle LinkYes My YouTube Account was Hijacked Today and My Sincere ApologyYes My YouTube Account was Hijacked Today and My Sincere ApologyFireFLY6 Garage Hover Test and Y6 Propeller Configuration w/ NAZA V2FireFLY6 Garage Hover Test and Y6 Propeller Configuration w/ NAZA V2MWC Flip 1.5 RTF and Updated Top Case DesignMWC Flip 1.5 RTF and Updated Top Case Design3DR APM 2.6 Yaw Orientation for Autonomous Flight w/ Bixler Plane3DR APM 2.6 Yaw Orientation for Autonomous Flight w/ Bixler PlaneDroneBlocks with AirSim for Panorama SimulationDroneBlocks with AirSim for Panorama SimulationQAV400 / QAV500 3D Printed Landing Gear RevisitedQAV400 / QAV500 3D Printed Landing Gear RevisitedAPM 2.5 Hardware in the Loop (HIL) Simulation Testing Stabilize and RTL Flight Modes w/ X-PlaneAPM 2.5 Hardware in the Loop (HIL) Simulation Testing Stabilize and RTL Flight Modes w/ X-PlaneiPower 950kV Brushless Motor Cleaning on TBS Discovery Quadcopter - Working on Vibration ReductioniPower 950kV Brushless Motor Cleaning on TBS Discovery Quadcopter - Working on Vibration Reduction3D Printed Arm Extensions for DJI Flamewheel Frame using Makerbot Replicator 23D Printed Arm Extensions for DJI Flamewheel Frame using Makerbot Replicator 2Recruit Wing with PX4 Telemetry Using Raspberry Pi Zero, GSM Module, and Hologram IoT NetworkRecruit Wing with PX4 Telemetry Using Raspberry Pi Zero, GSM Module, and Hologram IoT NetworkNAZA Lite and TBS Discovery with Turnigy 9XR 3 Flight Modes - GPS Attitude, Manual, & FailsafeNAZA Lite and TBS Discovery with Turnigy 9XR 3 Flight Modes - GPS Attitude, Manual, & FailsafeQAV400 Garage and Backyard Maiden Flight w/ NAZA and Turnigy 9X 3 Flight ModesQAV400 Garage and Backyard Maiden Flight w/ NAZA and Turnigy 9X 3 Flight ModesAwesome $5 FPV Racing Simulator FPV Freerider Setup with FrSky TaranisAwesome $5 FPV Racing Simulator FPV Freerider Setup with FrSky Taranis3D Printed GPS/Compass Stand for APM and Pixhawk Multirotors3D Printed GPS/Compass Stand for APM and Pixhawk MultirotorsHoverGames Drone Vibration Analysis w/ PX4 Flight Review - Don't Let Vibrations Kill Your MultiRotorHoverGames Drone Vibration Analysis w/ PX4 Flight Review - Don't Let Vibrations Kill Your MultiRotorDroneMaps FAA Sectional Charts and UAS Facility Maps for Android and iOS Coming SoonDroneMaps FAA Sectional Charts and UAS Facility Maps for Android and iOS Coming SoonHow I Design and 3D Print Parts with Rhino 3D and MakerBot Replicator 2 - The Magic Coin PaddleHow I Design and 3D Print Parts with Rhino 3D and MakerBot Replicator 2 - The Magic Coin PaddleAutonomous Aerial Video of Onion Creek using Pixhawk and ArduCopter 3.2Autonomous Aerial Video of Onion Creek using Pixhawk and ArduCopter 3.2RAD MAVLink Bridge Installation Script for Raspberry PiRAD MAVLink Bridge Installation Script for Raspberry Pi
Яндекс.Метрика