Spyder Auto How to Install: 2006-2010 Lexus IS250/350 LED Headlights
This video demonstrates how to install a set of Spyder Auto 2006-2010 Lexus IS250/350 LED Headlights. This complete how-to tutorial guides you, from start to finish, through the installation process. It also offers helpful tips throughout to facilitate a successful installation.
-= TOOLS NEEDED =-
1. Small flat-head screwdriver
2. Phillips screwdriver
3. Ratchet
4. Long extension
5. 10mm deep socket
-= INSTALLATION INSTRUCTIONS =-
1. Remove the eight 10mm screws under the bumper.
2. Remove the two fasteners on the fender liner.
(Turn 90-degrees counter-clockwise and pop-off)
3. Pull back the fender liner.
4. Remove the 10mm screw holding the bumper to the fender.
5. Open the hood.
6. Remove the eleven push-pin fasteners on the radiator shroud.
7. Remove the radiator shroud.
8. Remove the three push-pin fasteners as well as the Phillips hood stopper.
(Above the bumper near inner-side of headlight)
9. Remove the 10mm bolt in the center of the bumper.
10. Unseat the bumper.
(Loosen it, do not remove it)
11. Disconnect the fog light harness.
(There are three plugs – one on passenger side, two on driver)
12. Remove the bumper.
13. Remove the three 10mm bolts securing the headlight.
14. Disconnect the headlight harness.
15. Remove the headlight.
16. Transfer over the bumper bracket.
(Take it off of the OEM light and transfer onto new light)
17. Bring new light over to car.
18. Seat the new headlight.
19. Connect the wiring harness.
20. Reinstall the three 10mm bolts securing the headlight into place.
(Note: Two smaller bolts and one longer one near the fender-bumper area)
21. Bring front bumper nearby.
22. Reconnect the fog light plugs.
(There are three plugs)
23. Reinstall the center 10mm bolt holding the bumper in place.
24. Reinstall the three push-pins holding the bumper into place.
23. Reinstall the Phillips-screw hood stopper.
24. Reinstall the 10mm screw on the side of the bumper.
25. Reinstall the two fasteners on the fender-liner.
26. Reinstall the eight 10mm screws underneath the bumper.
27. Reinstall the radiator shroud.
28. Reinstall the eleven push-pin fasteners on the radiator shroud.
29. Close the hood.
30. Installation completed.
Видео Spyder Auto How to Install: 2006-2010 Lexus IS250/350 LED Headlights канала Spyder Auto
-= TOOLS NEEDED =-
1. Small flat-head screwdriver
2. Phillips screwdriver
3. Ratchet
4. Long extension
5. 10mm deep socket
-= INSTALLATION INSTRUCTIONS =-
1. Remove the eight 10mm screws under the bumper.
2. Remove the two fasteners on the fender liner.
(Turn 90-degrees counter-clockwise and pop-off)
3. Pull back the fender liner.
4. Remove the 10mm screw holding the bumper to the fender.
5. Open the hood.
6. Remove the eleven push-pin fasteners on the radiator shroud.
7. Remove the radiator shroud.
8. Remove the three push-pin fasteners as well as the Phillips hood stopper.
(Above the bumper near inner-side of headlight)
9. Remove the 10mm bolt in the center of the bumper.
10. Unseat the bumper.
(Loosen it, do not remove it)
11. Disconnect the fog light harness.
(There are three plugs – one on passenger side, two on driver)
12. Remove the bumper.
13. Remove the three 10mm bolts securing the headlight.
14. Disconnect the headlight harness.
15. Remove the headlight.
16. Transfer over the bumper bracket.
(Take it off of the OEM light and transfer onto new light)
17. Bring new light over to car.
18. Seat the new headlight.
19. Connect the wiring harness.
20. Reinstall the three 10mm bolts securing the headlight into place.
(Note: Two smaller bolts and one longer one near the fender-bumper area)
21. Bring front bumper nearby.
22. Reconnect the fog light plugs.
(There are three plugs)
23. Reinstall the center 10mm bolt holding the bumper in place.
24. Reinstall the three push-pins holding the bumper into place.
23. Reinstall the Phillips-screw hood stopper.
24. Reinstall the 10mm screw on the side of the bumper.
25. Reinstall the two fasteners on the fender-liner.
26. Reinstall the eight 10mm screws underneath the bumper.
27. Reinstall the radiator shroud.
28. Reinstall the eleven push-pin fasteners on the radiator shroud.
29. Close the hood.
30. Installation completed.
Видео Spyder Auto How to Install: 2006-2010 Lexus IS250/350 LED Headlights канала Spyder Auto
Показать
Комментарии отсутствуют
Информация о видео
Другие видео канала
How to change / replace the headlamp ballast on a Lexus IS250 /IS350 / ISF *STEP-BY-STEP*VLAND LED Headlights for my 2007 Lexus IS 350!SPECDTUNING INSTALLATION VIDEO: 2006-2009 LEXUS IS250 LED PROJECTOR HEADLIGHTS2008 Lexus IS250 Headlight UpgradeHow To Get 2013 Headlights on Any Lexus IS for $400 Or Less!How To RESTORE your Headlights the PROPER way!VLAND Headlight Review & DIY Install Lexus 2006-2013 IS250 IS350 IS-F Triple Beam LEDHow to Replace Lexus IS250 Headlight Low Beam Bulb 2009Here's How I'm Using Cheap eBay Parts to Update My Lexus ISF Rear EndDIY: 2006-2013 LEXUS IS250/ IS350 - Factory HID to LED conversion, STEP BY STEPDRL Projector headlights Lexus Is 250/350/ISFhow to remove lexus IS 2nd generation bumper DIY.DIY: 2008 Lexus ISF Headlights and Installing 2013 OEM LED HeadlightsPopular Mods for Lexus IS 250 and IS 350Best Mods for Your 2IS Under $100!!How to replace full headlight assembly with HID / AFS on 2008 Lexus ES350K2 MOTOR INSTALLATION VIDEO: 2006-2009 LEXUS IS250 LED PROJECTOR HEADLIGHTSVLand LED Headlights Install! | Lexus IS250Fresh Headlights for the Lexus IS! From Unique Style Racing + DEPOAll The Mods on My 2007 Lexus IS 350! (The Evolution from 2017-2020)