- Популярные видео
- Авто
- Видео-блоги
- ДТП, аварии
- Для маленьких
- Еда, напитки
- Животные
- Закон и право
- Знаменитости
- Игры
- Искусство
- Комедии
- Красота, мода
- Кулинария, рецепты
- Люди
- Мото
- Музыка
- Мультфильмы
- Наука, технологии
- Новости
- Образование
- Политика
- Праздники
- Приколы
- Природа
- Происшествия
- Путешествия
- Развлечения
- Ржач
- Семья
- Сериалы
- Спорт
- Стиль жизни
- ТВ передачи
- Танцы
- Технологии
- Товары
- Ужасы
- Фильмы
- Шоу-бизнес
- Юмор
Would Be Fine With Two Soldering Irons But Just Not Keeping Them On For Too Long#FLUX #Motherboard
Would Be Fine With Two Soldering Irons But Just Not Keeping Them On For Too Long
#FLUX #MotherboardRepair #electronicstechnician #solder #solderingstation
Видео Would Be Fine With Two Soldering Irons But Just Not Keeping Them On For Too Long#FLUX #Motherboard канала Rework Station
#FLUX #MotherboardRepair #electronicstechnician #solder #solderingstation
Видео Would Be Fine With Two Soldering Irons But Just Not Keeping Them On For Too Long#FLUX #Motherboard канала Rework Station
Комментарии отсутствуют
Информация о видео
18 ч. 60 мин. назад
00:00:18
Другие видео канала
Damaged USB Port That Is To Be Replaced With A Woking One.#motherboardrepair #solderingiron #flux
Kapton Tape On Each Side For This Task#flux #reworkstation #motherboardrepair #electronicstechnician
Just in The Clearing Of The Board So That The Replacement Can Be Soldered#motherboardrepair
A Couple Of Taps On One Side Then Got The Rest With The First Try. Just Needed To Add Some Flux
Comparing The MOSFET With Replacement Component To Be Soldered On The Board#ElectronicsTechnician
63 Sn tin wire for best results #motherboardrepair #electronicstechnician #automobile #solderingiron
Putting The Soldering Flat Iron Tip Aside#electronicstechnician #solderingiron #solderingstation
Just Got Enough Space For The Solder Wick To Go Under The Chip For Desoldering #solderingiron #flux
Had Put The Wide Flat Soldering Iron Tip With Solder Under The Flex Cable To Desolder It.#solder
Adding A Tack Solder For Replacing This Connector On The Board#solderingstation #solderingiron
Adding Some Flux First Then Get Some Solder On The Soldering Iron And Ready To Desolder It#soldering
Sliding The Soldering Iron Back & Forth To The Sides After Putting Some Flux And Adding More Solder
Weekend Flux And Hot Air On The Rework For This Component #motherboardrepair #flux #reworkstation
Soldering Iron Flat Tip On A Re-Used Solder Wick For This Double USB Port#solderingiron
Replacing The Flex Cable With The Connector Using More Solder And Soldering Iron Flat Tip#motherboar
Was Gonna Try To Pick The Connector Up With Some Tweezers But Seems Easier To Handpick It#motherboar
After The Soldering Iron On The Wire Then Its Now The Soldering Iron On The Solder Wick Braid For
Just Not Keeping The Speaker Cable In The Port#solderingiron #solderingstation #electronicstech
Was Going For A Wire Or A Used Solder Wick But Decided To Put On The Rework Station#electronicstech
After The Two Wide Soldering Iron Tips Is A Single Wide Soldering Iron Solder Clearing And Some
